DutchWest 16 설치 지침
{카테고리_이름} DutchWest 16에 대한 설치 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. DutchWest 16 4 페이지. Inner top replacement kit for the dutchwest extra large convection heaters
페이지 인쇄Inner Top Replacement
Installation Instructions
Kit #0016
for the Dutchwest Extra-
Large Convection Heaters
General Information
The two-piece inner top kit for the Dutchwest Extra-
Large convection Heater fits 1990-93 units (model
2184, with two front doors) and 1993-97 units (model
2460, with a single front door).
The sides, front and inner back of the stove trap the in-
ner top. Replacing the original style inner top requires a
complete rebuild of the stove. Once the new style inner
top is in place, if you need to replace the insert you can
do so by removing only the stove top.
Work in a clear, well-lighted area. If possible, work out-
doors. If you must work indoors, use a drop cloth and
protect the surrounding area. Wear gloves, a dust mask
and protective eyewear.
Kit Contents:
• Inner top casting insert • Inner top insert
• Refractory insulator
• Refer to Figure 7 to identify parts.
Tools Required:
• Rubber mallet, or standard hammer and a block of
wood
• 7/16" open-end wrench
• 3/8" cold chisel, or old screwdriver
• Needle-nose pliers (for later units only)
• Wire brush, hand-held or rotary
• Stove cement and putty knife. The easiest way to ap-
ply cement is from a tube in a caulking gun. Other-
wise, use a putty knife to apply cement from tube.
• Penetrating oil. Use Marvel Mystery Oil, Liquid
Wrench or similar; WD-40 is not strong enough for
this work.
• Automotive anti-seize compound
• Shop Vac with very good filter. Do not use a regular
household vacuum on soot - it is fine enough to pass
right through most common filters.
• Drop clot or tarp
• 2 pieces of Interam gasket
Disassembly Procedure
1. Make sure the stove is completely cool before you
begin. Remove ashes and dispose of them properly.
An empty ashpan is a handy tray for hardware and
small parts.
2. Remove the probe thermometer from the stove
top. Some units have a small chrome sleeve on the
probe shaft; be sure to keep track of this if it is loose.
3. Lift off the front door(s) and the side door. You can
remove the doors by wiggling them back and forth,
and lifting at the same time.
4. Unfasten and remove the top. (Fig. 1) A bolt at each
corner holds the top to the rest of the stove body.
There is a gasketed seal between the stove top and
the rest of the body. Lift off the stove top and set it
aside, upside down. Check the gasket for compres-
sion or wear; replace if necessary.
Loosen
all four(4)
Bolts Before
Removal
ST790
Fig. 1 Remove four (4) bolts to release the stove top.
5. Lift out the decorative front brass bar, the refractory
insulator and the catalyst. (Figs. 2 and 3) Be careful
with the catalyst, as it is fragile. Place the insulator
in a sealed plastic bag pending disposal. Check the
combustor for major cracking or crumbling. Refer to
the stove manual for details on evaluating the cata-
lyst.
From this point on, penetrating oil will help to release
hardware. Use automotive anti-seize compound
when you replace hardware, to ease future repairs.
Fig. 2 Remove the refractory insulator.
Loosen, then
remove these
bolts
St790
remove stove top
5/04
Refractory
Insulator
7001208 8/08 Rev. 3