Datasensor TL46-W 사용 설명서 - 페이지 4

{카테고리_이름} Datasensor TL46-W에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Datasensor TL46-W 4 페이지. Contrast sensor

페이지 인쇄

Select "dLOF" from the parameter menu to set DELAY OFF function.

The parameter programming is accessed by pressing

The previously set delay value appears on the display.

Pressing

the delay value is increased or decreased by one step of

1 ms until a maximum delay of 100ms. Keeping press

value is increased or decreased by incremental step. The setting of a delay

different from zero is signalled by the DELAY LED on. Press

the value and return to the parameter menu.

PNP/NPN output setting

The digital output can be configured as PNP or NPN.

Select '_PnP' or '_nPn' in the parameter menu to switch the output.

The previously set output switches by pressing

UP/DOWN DISPLAY setting

The selection of the UP/DOWN display sets the reading direction on the

display.

Select "dSUP" or "dSdn" in the parameter menu to set the UP or DOWN

direction.

Press

to switch the reading direction previously set.

ON/OFF DISPLAY setting

Turn off the display during normally working to save power consumption.

Setting the OFF mode, when the sensor is functioning normally, the display is

OFF. It turns on for 5s after a keyboard command. Select "dSOn" or "dSOF"

in the parameter menu to set the display ON or OFF.

Press

to switch the display mode previously set.

RESET of default parameters

Select "rSEt" in the parameter menu to reset the default parameters.

The "rSEt" text blinks when pressing

Releasing the push-button the sensor returns to normal functioning.

The default reset parameters are:

PARAMETER

DISPLAY

DESCRIPTION

________

Emission

Green

________

DARK/LIGHT mode

Light

Threshold

2050

Hysteresis

Medium (Normal)

Delay ON and OFF

Deactivated

Digital output

PNP output

Display

Display UP ON

NOTE: if the parameters are reset before turning the sensor off, when

repowered the "rSEt" text blinks on the display for 3s before returning

to normal visualisation.

Saving parameter set - "SAVE"

Select "SAVE" to save the parameter setting

The parameters are saved pressing

and releasing it the display returns to

normal visualisation.

NOTE: Set the data, the operator exits from the menu using the "SAVE"

or "RESET" function. If these operations are not carried-out 30s after

the last setting, the sensor returns to normal mode saving the

parameters changed.

ACCESSORY FUNCTIONS

REMOTE INPUT

The REMOTE signals carries-out the acquisition functions without using the

push-button.

The REMOTE wire connected to +Vdc is equal to pressing the

button. Whereas, if the REMOTE wire is connected to GND or not connected

the delay

it is equal to not pressing the

push-button.

to confirm

REMOTE

PUSH-BUTTON

NOT PRESSED

+Vdc

PRESSED

- The duration of the REMOTE wire connection to +Vdc determines the

acquisition type:

STATIC

>1s

REMOTE

DET.

GND

Mark detection

DYNAMIC

REMOTE

DET.

GND

Dynamic detection

(begin) start

DARK/LIGHT input

The DARK/LIGHT signal allows the operator to select the DARK/LIGHT

operating mode for dynamic detection.

In the LIGHT mode the output is active with light marks on dark backgrounds,

in the DARK mode the output is active with dark marks on light backgrounds.

The connection of the DARK/LIGHT wire to Vdc sets the DARK mode.

If connected to 0V or not connected set the LIGHT mode.

DARK/LIGHT

MODE

LIGHT

+Vdc

DARK

EX-II-3DG IP67 T6

T6 (<85°C)

Temperature class:

Max. Power consumption 1000 mW at 30 Vdc

Max. Internal capacitance 100 nF

Internal inductance:

negligible

DECLARATION OF CONFORMITY

We DATASENSOR S.p.A. declare under our sole responsibility that these products are conform to the

2004/108 CEE, 73/23 CEE Directives and successive amendments.

WARRANTY

DATASENSOR S.p.A. warrants its products to be free from defects.

DATASENSOR S.p.A. will repair or replace, free of charge, any product found to be defective during the

warranty period of 36 months from the manufacturing date.

This warranty does not cover damage or liability deriving from the improper application of

DATASENSOR products.

DATASENSOR S.p.A. Via Lavino 265

40050 Monte S. Pietro - Bologna - Italy

Tel: +39 051 6765611

Fax: +39 051 6759324

http://www.datasensor.com

e-mail: [email protected]

DATASENSOR S.p.A. cares for the environment: 100% recycled paper.

DATASENSOR S.p.A. reserves the right to make modifications and improvements without

prior notification.

826003101 Rev.A

CTi Automation - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.ctiautomation.net - Email: [email protected]

push-

Background detection

Dynamic detection

end