Datasensor SDS10-5-M12-35 사용 설명서

{카테고리_이름} Datasensor SDS10-5-M12-35에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Datasensor SDS10-5-M12-35 2 페이지.

페이지 인쇄
SDS5-5 SERIES
INSTRUCTION MANUAL
CONTROLS
OUTPUT LED
The yellow LED indicates the output status.
STABILITY LED
The green LED ON indicates that the received signal has a reserve
greater than 30% compared to the output switching value.
TRIMMER
The 4-turn trimmer can be used to adjust the operating distance; the
distance increases turning the trimmer clockwise.
CONNECTIONS
BROWN
1
+
10 ... 30 Vdc
WHITE
2
NC
100 mA
BLACK
4
NO
100 mA
BLUE
3
0 V
M12 CONNECTOR
2
1
3
4
CABLE VERSIONS
AXIAL VERSION
93.6
53.5
OUTPUT LED
TRIMMER
STABILITY LED
8.8
75.9
9.2
RADIAL VERSION
M18x1
TRIMMER
OUTPUT LED
STABILITY LED
21.4
TECHNICAL DATA
Power supply:
Ripple:
Current consumption
(output current excluded):
Output:
Output current:
Output saturation voltage:
Response time:
Switching frequency:
Indicators:
Setting:
Operating temperature:
Storage temperature:
Electric shock protection:
Cutoff distance adjustment range:
Operating distance:
Emission type:
Ambient light rejection:
Vibration:
0.5 mm amplitude, 10 ... 55 Hz frequency, for every axis (EN60068-2-6)
Shock resistance:
LIGHT/DARK selection:
Housing:
Optics head:
Lenses:
Protection class:
Connections:
Weight:
DIMENSIONS
M12 CONNECTOR VERSIONS
AXIAL VERSION
84.7
18.8
53.5
TRIMMER
OUTPUT LED
STABILITY LED
8.8
75.9
RADIAL VERSION
TRIMMER
M18x1
OUTPUT LED
STABILITY LED
M12
M12
21.4
mm
10 ... 30 Vdc; reverse polarity protection
2 Vpp max.
30 mA max.
NC and NO, NPN or PNP; 30 Vdc max. (short-circuit protection)
100 mA max.
1 V max NPN versions / 2 V max PNP versions
2.5 ms max.
200 Hz max.
OUTPUT LED (YELLOW) / STABILITY LED (GREEN)
operating distance 4-turn trimmer wiper idles
-25 ... 55 °C
-25 ... 70 °C
Class 2
50 ... 100 mm
from 20 ... 50 mm to 0 ... 100 mm depending from cutoff adjustment
RED (660 nm)
according to EN 60947-5-2
11 ms (approx. 30 G) 6 shock for every axis (EN60068-2-27)
LIGHT mode on NO output
ABS UL 94V-O
PVC
Glass
IP67 (TYPE 1 ENCLOSURE)
2 m cable ∅ 5 mm / M12 4-pole connector
100 g. max. cable versions / 30 g. max. connector versions
SETTING
Position the sensor and turn the operating distance trimmer to
maximum.
Place the target opposite the sensor at a slightly greater distance than
desired.
Turn the trimmer counterclockwise until the sensor switches.
Verify the adjustment moving the target closer and further the sensor;
tune the adjustment if necessary.
It is recommended to operate with the stability LED turned ON.
The white/grey remission diagram is shown below:
12%
10%
90° VERSION
8%
6%
4%
2%
0%
0
20
40
60
80
100
DISTANCE (mm)
Grey test card (18% reflectance) cutoff point variation relative to white test
card (90% reflectance).
DECLARATION OF CONFORMITY
We DATASENSOR S.p.A. declare under our sole responsibility that
these products are conform to the 89/336 CEE, 73/23 CEE Directives
and successive amendments.
WARRANTY
DATASENSOR S.p.A. warrants its products to be free from defects.
DATASENSOR S.p.A. will repair or replace, free of charge, any product
found to be defective during the warranty period of 36 months from the
manufacturing date.
This warranty does not cover damage or liability deriving from the
improper application of DATASENSOR products.
DATASENSOR S.p.A. Via Lavino 265
40050 Monte S. Pietro - Bologna - Italy
Tel: +39 051 6765611
Fax: +39 051 6759324
http://www.datasensor.com
DATASENSOR S.p.A. cares for the environment: 100% recycled
paper.
DATASENSOR S.p.A. reserves the right to make modifications
and improvements without prior notification.
826000263 Rev.C
STRAIGHT
VERSION
120