DataStor DT51UN-A 설치 매뉴얼 - 페이지 2
{카테고리_이름} DataStor DT51UN-A에 대한 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. DataStor DT51UN-A 2 페이지. Scsi 50pin removable tray & frame, aluminum
페이지 인쇄Install Hard Drive into tray
NOTE: Please reference the documentation that came with your
hard drive for diagrams which show the SCSI pin location(s) on
your drive.
1. Open your DataTrans tray by pulling the side of the tray cover
away from the railing and firmly lifting of the cover. If you have
difficulty, try using a pen knife or watchmaker's screw driver
to separate the cover from the railing. NOTE: You can remove
either the top or bottom cover in this fashion, and the drive
can be mounted/accessed with either or both of the covers
removed.
2. Inside your tray you will find several sets of cabling, including
a four-pin power connector, a 50pin HDD controller connector,
a set of 5 wires for SCSI ID, and a set of two wires for the
Drive Activity LED (See Figure Four).
3. Referencing the manual that came with your drive, plug the
SCSI ID cables into the back of the drive. Figure Five provides
a nomenclature color diagram for the SCSI ID cabling inside
the tray.
NOTE: Some drive manufacturers list the SCSI ID block
jumpers as 0,1 and 2 as opposed to 1,2, and 4. If this is the
case with your drive, translate as follows 0=1 signal, 1=2 signal,
and 2=4 signal.
4. If you desire, plug the Drive Activity Cable into the appropriate
connector on your drive.
5. Plug the four-pin power connector and the 50pin HDD controller
connector into the drive.
6. Mount the drive into the tray using the four screws provided.
7. Replace the cover by following the reverse procedure for
removing it in step 1.
Install Tray into Frame
1. Set the SCSI ID using the rotary switch located on the bottom
right of the frame (Figure 6). If you are planning on using an
external SCSI ID switch set the rotary to "0". Do not confuse
the SCSI ID cables with the Drive Activity Cable, which is a
paired cable on the same terminal which consists of one Black
wire and one Red wire (Red is signal, Black is ground).
2. Insert your tray into it's frame as defined in step 3 of "Install
the Frame".
3. Insert a key from the set provided into your tray lock, and turn
the key counter clockwise to lock the tray - the drive is now
ready to receive power, and should power up normally when
your system is on. NOTE: The unit will not power up until the
tray is locked into the frame.
Replace Enclosure Cover
1. Following the documentation provided by the manufacturer of
your enclosure, replace the cover of the enclosure.
Phone (800) 777-6621 / Fax: (949) 833-9600 / Web Site: www.dstor.com
Installation Guide - DataTrans 50 pin Aluminum Removable Tray&Frame, Rev 1.0 - July 1998 - P/N DT51UN-A
Copyright 1999 by DataStor, Inc. All rights reserved. No part of this document may be reproduced in any form without prior written consent from DataStor. The information and specifications in this document are subject to change without
notice. Changes to this document are incorporated in new versions. DataStor, and the DataStor logo are reqistered trademarks of DataStor, Inc. Other trademarks used herein are the property of their respective owners. This document
was printed in the United States Of America.
DataStor, 12601 Monarch Street -- Garden Grove, CA 92841
Wiring (Inside Tray)
Figure 4
Power
SCSI ID
Cable
Cables
Figure 5
Orange
Red
Yellow
=
=
=
=
Figure 6
SCSI Switch
Back of Tray
50pin HDD
Connector Cable
Drive Activity
Signal Leads
Brown