Frigidaire Designer Series 사용 및 관리 매뉴얼 - 페이지 7

{카테고리_이름} Frigidaire Designer Series에 대한 사용 및 관리 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Frigidaire Designer Series 11 페이지. Electronic control a/c
Frigidaire Designer Series에 대해서도 마찬가지입니다: 제품 정보 (1 페이지), 소유자 매뉴얼 (14 페이지), 사용 및 관리 매뉴얼 (20 페이지), 사용 및 관리 매뉴얼 (20 페이지), 설치 지침 매뉴얼 (8 페이지), 사용 및 관리 매뉴얼 (13 페이지), 사용 및 관리 매뉴얼 (11 페이지), 사용 및 관리 매뉴얼 (20 페이지), 사용 및 관리 매뉴얼 (20 페이지), 소유자 매뉴얼 (12 페이지), 소유자 매뉴얼 (20 페이지), 소유자 매뉴얼 (14 페이지), 사용 및 관리 매뉴얼 (11 페이지), 사용 및 관리 매뉴얼 (11 페이지), 사용 및 관리 매뉴얼 (11 페이지), 사용 및 관리 매뉴얼 (20 페이지)

페이지 인쇄

Air Conditioner Features

(continued)

TO OPERATE ON FAN ONLY:

PRESS MODE

CHOOSE FAN

TO USE THE ENERGY SAVER

FEATURE:

PRESS MODE

ENERGY SAVER

TIMER: DELAY STOP / START

FEATURE

DO THIS:

PRESS

TIMER BUTTON

SZ000728(En)-Yaokong

YOU WILL SEE:

DO THIS:

BUTTON

ONLY

YOU WILL SEE:

DO THIS:

BUTTON

CHOOSE

YOU WILL SEE: TIMER SETTING

LIGHT On

Note: Use this function only when cooling is not desired, such

as for room air circulation or to exhaust stale air(on some

models). (Remember to open the vent during this function, but

keep it closed during cooling for maximum cooling efficiency.)

You can choose any fan speed you prefer.

During this function, the display will show the actual room

temperature, not the set temperature as in the cooling mode.

LIGHT On

Note: In this mode, the fan will continue to run for 3 minutes

after the compressor shuts off. The fan then cycles on for 2

minutes at 10 minute intervals until the room temperature is

above the set temperature, at which time the compressor turns

back on and cooling stars.

LIGHT On

Note: For Delay Stop, the unit must be in the On position.

Note: For Delay Start, the unit must be in the Off position.

To adjust timer setting, tap or hold the UP arrow(

arrow(

) to change delay timer at .5 hour increments, up to 10

hours, then at 1 hour increments up to 24 hours. The control will

count down the time remaining until start (8, 7.5, 7, etc.). The Delay

Start mode automatically selects cooling with maximum Fan Speed.

The temperature maintained will be the same as previously set. To

change the set temperature, press "COOL" then Up or Down ar-

rows until the desired temperature is indicated on the display. After

5 seconds, the control will automatically change the display back

to the hours remaining until the unit will start/stop. Turning the unit

"ON" or "OFF" at any time will cancel the Delay Start/Stop function.

The Delay Start/Stop Feature will work until the unit either starts or

stops. Once that happens the above steps have to be repeated

again.

09/20/2005, 5:30 PM

) or the DOWN