Frigidaire Designer Series 사용 및 관리 매뉴얼 - 페이지 13

{카테고리_이름} Frigidaire Designer Series에 대한 사용 및 관리 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Frigidaire Designer Series 20 페이지. Electronic control a/c
Frigidaire Designer Series에 대해서도 마찬가지입니다: 사용 및 관리 매뉴얼 (11 페이지), 제품 정보 (1 페이지), 소유자 매뉴얼 (14 페이지), 사용 및 관리 매뉴얼 (20 페이지), 설치 지침 매뉴얼 (8 페이지), 사용 및 관리 매뉴얼 (13 페이지), 사용 및 관리 매뉴얼 (11 페이지), 사용 및 관리 매뉴얼 (20 페이지), 사용 및 관리 매뉴얼 (20 페이지), 소유자 매뉴얼 (12 페이지), 소유자 매뉴얼 (20 페이지), 소유자 매뉴얼 (14 페이지), 사용 및 관리 매뉴얼 (11 페이지), 사용 및 관리 매뉴얼 (11 페이지), 사용 및 관리 매뉴얼 (11 페이지), 사용 및 관리 매뉴얼 (20 페이지)

페이지 인쇄
Frigidaire Designer Series 사용 및 관리 매뉴얼

Dishwasher Dispenser

& Detergents
Rinse Aid
Rinse aid greatly improves drying and reduces
water spots and filming. Water "sheets" off
dishes rather than forming water droplets that cling
and leave spots.
A dispenser, located next to the detergent cup,
automatically releases a measured amount of
rinse aid during the last rinse. If spotting and poor
drying are problems, increase the amount of rinse
aid dispensed by rotating the dial to a higher
number. The dial is located under the dispenser
cap. The indicator will be dark when full and will
show clear when it is time to refill. On models with
a STATUS window, LO will appear at the end of
the cycle indicating that it is time to refill.
To add liquid rinse aid, turn dispenser cap 1/4 turn
counterclockwise and lift out. Pour in rinse aid until
liquid touches the indicated fill level. Replace cap.
Do not overfill since this can cause oversudsing.
Wipe up any spills with a damp cloth.
The dispenser holds enough for 35 to 140 washes,
depending on setting.
Dispenser Opening
Less
Dispenser Cap
(continued)
Indicator
More
Adjustable setting
Factors Affecting
Performance
Water Pressure
The hot water line to dishwasher must provide
water pressure between 20 and 120 psi.
Low water pressure may occur when laundry or
showers are in operation. Wait until water use is
reduced before starting dishwasher.
Water Temperature
Hot water is needed for best dishwashing and
drying results. Water entering dishwasher should
be at least 120°F (49°C) to give satisfactory
results.
To check water temperature entering dishwasher:
• Turn on hot water faucet nearest dishwasher
for several minutes to clear cool water from
pipes.
• Hold a candy or meat thermometer in stream of
water to check the temperature.
• If temperature is below 120°F (49°C), have a
qualified person raise the hot water heater
thermostat setting.
Important: Before starting a cycle, run hot
water to clear cool water from pipe.
The HEAT DRY option in combination with
rinse aid will enhance drying performance. The
energy required to use the HEAT DRY option
costs pennies per cycle. You may choose not
to select the HEAT DRY option; however you
will have items in your dish load that will not be
completely dry at the end of the cycle.
13