Austin Springs AS-RO-75 소유자 매뉴얼 - 페이지 6

{카테고리_이름} Austin Springs AS-RO-75에 대한 소유자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Austin Springs AS-RO-75 9 페이지. Reverse osmosis water filter system

페이지 인쇄

Step 6: Install Reverse Osmosis Membrane

1 –

1 Disconnect the white

tubing from the Inlet quick-fitting on the membrane housing cap

Unscrew the cap

Tip #1)

(The small housing wrench may be needed to loosen the cap.)

2 Remove the membrane from its sealed bag Follow the flow direction sign on the membrane,

and firmly push into the housing Insert the small end

large end is even with the housing opening

3 Before screwing the housing cap back on, check that the O-ring is fitted evenly on the

membrane housing

(cap does NOT have O-ring)

half-turn Do not overtighten Do not reconnect tubing at this point

Step 7: Tubing Hook up

Connect the Tubes as shown

(See Tip #1)

Your system is equipped

with an Automatic Shut-Off

Valve allowing your system to turn off

the water supply to the RO system, using

pressure from the pure water side of the

system. It saves water, extends filter life,

and improves the performance of

your unit.

head first until the

(two black O-rings)

Use the small housing wrench to tighten about a

Faucet Base

Storage Tank

Small Faucet Nipple

Water Feed Adapter

Step 8: System Start Up

1 Organize tubing and check each for kinks Turn Tank Shut-Off Valve to "OFF" Have a towel

ready to catch leaks

2 Keep the tubing to the RO membrane inlet unattached

a bucket until the water runs clear Then re-connect the tubing to the RO membrane

3 Turn on the Feed Water Adapter valve Then, slowly turn on the Cold Water Supply Valve and

check for leaks Leaks can result when: tubing is not fully inserted, the 0-ring is not secure,

Housing/Cap are not tightened properly

4 After any leaks have been resolved, turn on the RO Drinking Faucet

5 RO water should start dripping within 5 minutes Let run for 10 minutes, allowing the system

to flush Water will be dark due to loose carbon from filters, it will turn clear

(except tank)

6 Turn off the RO Drinking Faucet Turn Tank Shut-Off Valve to "ON" Allow tank to fill It should

(see

1 –

take between 1

to 3 hrs

7 When tank is full, turn on RO Drinking Faucet to flush water from tank DO NOT use first tank

of water Water will surge from faucet When it slows to a trickle, the tank is empty and can be

refilled for use

8 For the first two weeks following installation,

check for leaks daily *Optional: Place a bucket

under system or use the included Water

Detector Alarm in case of leaks

9 Test RO water periodically to verify effective

reduction of total dissolved solids

TDS of source water is 100ppm, RO water

should be less than 10ppm

If you have any questions or concern about our

products, please don't hesitate to call or email

us We will do all that we can to make your sure

you are delighted with your purchase

If you are happy with our product and service,

please show your support by writing a product

review on Amazon, even if it's a simple single

line It only takes a minute, but means a lot to

us! Thank you!

(Step 6)

(longer for colder weather)

measures Total Dissolved Solids. TDS

are expressed in units of mg per unit volume

of water (mg/L), or referred to as parts per

million (PPM). With a TDS meter, you can easily

If the

(TDS)

compare the quality of RO water

Congratulations!

Now that your system is installed

enjoy clean healthy water right from your tap.

We provide a 90-day money back guarantee,

one-year Manufacturer Warranty and lifetime

tech support for all of our products These

benefits are only available, however, when

you confirm your order information and

activate your warranty You may activate

your warranty by mail or online by going to

AustinSprings com/warranty

, flush the first three stages into

(Tip #1)

A TDS meter

is a handheld device that

with your original

source water.