AUSTRAL CLOTHES HOISTS ADD-A-LINE 설치 지침

{카테고리_이름} AUSTRAL CLOTHES HOISTS ADD-A-LINE에 대한 설치 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. AUSTRAL CLOTHES HOISTS ADD-A-LINE 2 페이지. 2.4m wall mount

페이지 인쇄
AUSTRAL CLOTHES HOISTS ADD-A-LINE 설치 지침
ADDALINE (duo) 2400x1500mm
Parts supplied:
2 x Pre-Assembled (double) Side Arms (1500mmdeep)
2 x Front spacer Bars (1037mm x 22mm x 22mm) – outer frame
2 x Front spacer Bars (985mm x 22mm x 22mm) – inner frame
2 x Front Joiner Bars (535mm x 25mm x 25mm)
Cord 40m
WALL MOUNT INSTRUCTIONS
Due to the diversity of construction materials available, please consult your local Hardware Store or Builder for fixing
advice if required.
Mark drill holes using the Template supplied:
Check the fixing surface is flat and structurally sound. Mark the top drill hole approximately 50mm above user's
head height. For general installation where the user's height is unknown, mark the top drill hole between 1850-
1900mm above finished ground level. Consider future paving or path settings if not installed.
Mark the drill holes 2400mm apart, ensuring the top marks are level. If your available space is shorter, refer to
*instruction below on how to shorten the length.
Place Template over top hole, ensuring it is vertically plumb, mark the lower hole on each side. Drill the holes
using an 8mm drill bit and a hammer drill or variable speed drill. If fitting to a masonry wall, insert wall plugs
until they are flush with surface.
Attach one of the Pre-Assembled Side Arms (left and right Arms are supplied) to wall attaching the top screw only at this point.
Attach the other Side Arm. The two bent Side Arms should face towards each other. DO NOT TIGHTEN ANY OTHER BOLTS.
*To shorten the length (left to right) of a Fold Down Clothesline:
Mark the wall using the Wall Template on both sides within the available space, staying at least 50mm in from the edge of any
wall. Measure the distance between the left and right fixing points. Deduct the measured distance from the standard centre-to-
centre length – check point (1) above for your clothesline's centre to centre distance. The difference is the measurement that will
need to be cut off the Front Bar. For example: If you are installing a 2400mm long Fold Down onto a shorter wall, say the fixing
points are 2100mm apart, you will need to reduce the overall length of the Front Bar by 300mm (2400mm – 2100mm = 300mm).
Divide the difference by 2 (in this example: 300mm divided by 2 = 150mm). 150mm will need to be cut off one end of each Spacer
Bar for the Joiner Bar to remain in the centre of the Front Bar.
Do not cut the Joiner Bar. Insert a cut Spacer Bar into each end of Joiner Bar to form the new length Front Bar and proceed
with assembly. N.B. Remember to shorten the Back Bar on the Ground Mount Kit if the clothesline is to be installed as a free-
standing option.
Continue with installation
The Add-a-line is supplied with 4 spacer bars and 2 joiner bars. NOTE: The spacers are different lengths.
Assemble both sets of front bars. Insert the two shorter Spacer Bars into each end of the second Joiner Bar.
The longer Front Bar must be used on the larger frame and the shorter Front Bar must be used on the smaller frame.
Insert the longer Front Bar into one of the long Arms, then carefully maneuver the loose end into the opposite long Arm. Insert
the shorter Front Bar into the smaller Arms.
Ensure all bolts are secure but not over tight. Bolts on the sliding Brace should be loose enough to allow rotation by marginal finger
movement. The Catches must move freely to allow the Braces to lock and unlock.
AUSTRAL ADD-A-LINE 2.4M
WALL MOUNT INSTALLATION INSTRUCTIONS
AUSTRAL CLOTHES HOISTS PTY. LTD.
INCORPORATED IN VICTORIA
32-34 HYDRIVE CLOSE, DANDENONG SOUTH,
Tel 61 3 9799 8122 Fax 61 3 9799 8266
Website: www.australclotheshoists.com.au
Accessory Pack:
1 x Wall Template
2 x 16mm plastic end Caps for Side Braces
4 x 25mm plastic end Caps for Side 2ms
2 x Cord Knob
2 x Cord Tidy
4 x8mm wall plugs and 4 screws 6x50mm
A.B.N. 68 006 790727
VICTORIA 3175, AUSTRALIA