CookTek PTDS100 소유자 매뉴얼 - 페이지 7
{카테고리_이름} CookTek PTDS100에 대한 소유자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. CookTek PTDS100 10 페이지. Pizza thermal delivery system
Ennen kuin aloitat:
Varmista, että tämä virtajohto on tiukasti kiinnitetty CookTek:iin ENNEN laitteen pis-
tokkeen työntämistä pistorasiaan ja ennen käyttökokeilua.
● Älä koske keraamista levyä (keittotason päällä) heti käytön jälkeen. Astian
kuumuus siirtyy keraamiseen levyyn kuumentaen sen liian kuumaksi koskettaa.
● Tätä tuotetta saa huoltaa ainoastaan valtuutettu huoltopiste tai CookTekin
henkilökunta. Älä yritä avata laitetta ja suorittaa sille minkäänlaisia huoltotoimia.
Tietoja huollosta saat soittamalla CookTekiin numeroon +1-312-563-9600.
● Tämä laite täytyy suojamaadoittaa. Liitä ainoastaan oikein suojamaadoitettuun
pistorasiaan. Ennen käyttöä lue maadoitusohjeet ja sähköasennusvaatimukset
tämän lehtisen sivulta 3. Älä käytä jatkojohtoa.
Avant d'utiliser l'appareil Cooktop, effectuer les opérations suivantes :
● Retirer tous les matériaux d'emballage.
● Placer l'appareil sur une surface sèche, plane, solide, stable et non
inflammable.
● Placer l'appareil à distance de toute autre sources de chaleur et laisser un
espace libre d'au moins 5 cm (2 pouces) des deux côtés, à l'avant et à l'arrière
de celui-ci pour permettre la circulation de l'air.
Pour votre sécurité, ne jamais couper, déconnecter ou désactiver le raccordement
électrique (terre) de la prise de courant. Ne jamais utiliser un adaptateur ou une
rallonge électrique avec l'appareil Cooktop.
MISE EN GARDE : Une prise de courant incorrectement raccordée à la terre
engendre un risque de choc électrique. Pour toute question concernant ces
instructions de mise à la terre, consulter un électricien qualifié.
Avant de commencer :
S'assurer que le câble d'alimentation est solidement fixé à l'appareil CookTek
AVANT de raccorder l'appareil à une prise de courant et d'essayer de le faire
fonctionner.
● Ne pas toucher la plaque de céramique (ou la partie supérieure de l'appareil
Cooktop) immédiatement après utilisation. La chaleur de la casserole se
transmet à la plaque de céramique, aussi celle-ci est chaude au toucher.
● L'entretien de cet appareil ne peut être effectué que par un réparateur agréé ou
par un membre du personnel de CookTek. Ne jamais essayer d'ouvrir l'appareil
ni de le réparer. Pour des informations concernant l'entretien, contacter
CookTek au +1-312-563-9600.
● Cet appareil doit être raccordé à la terre. Le brancher exclusivement à une
prise de courant correctement raccordée à la terre. Avant utilisation, lire les
instructions de raccordement à la terre, ainsi que les exigences en matière
d'installation électrique figurant à la page 3 du présent manuel. Ne pas utiliser
de câble de rallonge.
FRENCH
13
NOTE: If the PTDS unit does not see any activity for an extended period of time,
you will initially hear two beeps and then you will see the "POWER" LED flash
constantly. This is NOT an error code, merely an indication that the unit has
entered a power saving "sleep" mode. To exit "sleep" mode, press the "RESET"
button.
ERROR CODES FOR GENERATION 3 PTDS UNITS
Error codes will be indicated by a number of beeps and the flashing "RESET" LED.
Count the number of beeps in a row. This will be the error number. If there is more
than one error condition, there will be a pause and then the unit will beep the next
error number. It will continue to repeat this cycle until the PTDS is reset.
To reset the PTDS from an Error mode, remove the bag from the unit and press the
"RESET" button. If the unit does not reset, turn the unit off, unplug the power cord,
wait 5 seconds, and then plug it in again.
Error Error Description Potential Cause
Push button is
Control membrane is
2
damaged
damaged
A metallic object may be
present on the charger
Current draw is too
3
or there may be
high
mechanical damage to
the work coil.
Fan broken, bad
Electronics are
4
ventilation, or ambient
overheating.
temperature problem.
7
Hardware failure
Inverter I/O problem
Bad AC source, board
8
Zero cross error
component failure
VaporVent bag not
Foreign object
centered properly or
9
detected
pressed down during the
charge phase.
VaporVent bag not
Current drop too
centered properly or
10
small after X
pressed down during the
seconds
charge phase
Unstable load.
Not a valid pellet, or bag
11
Current change is
was being jostled as it
too great.
was set down.
16
System error
CPU I/O problem
Action Required
To reset, unplug unit,
wait 5 seconds, and plug
in again
Remove bag and check
for foreign objects on
tray or inside bag. Retry.
Check airflow. Clear air
vents. Listen for fan
operation
To reset, unplug unit,
wait 5 seconds, and plug
in again.
Turn unit off, then on. If
problem persists, service
is required on device.
Remove bag and check
for foreign objects on the
tray or inside bag. Retry.
Remove bag and check
for foreign objects on
tray or inside bag. Retry.
Remove bag and check
for foreign objects on
tray or inside bag. Retry
To reset, unplug unit,
wait 5 seconds, and plug
in again.
Manual PTDS 10336_A USINTL
6