Bender ISOMETER iso685-D-B-CN 빠른 시작 매뉴얼

{카테고리_이름} Bender ISOMETER iso685-D-B-CN에 대한 빠른 시작 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Bender ISOMETER iso685-D-B-CN 8 페이지.

페이지 인쇄

快速操作手册 / Quick-start guide

ISOMETER® iso685...-CN

绝缘监视仪

这本快速入门指南适用于下列型号 : iso685-D-CN, W-D-CN,

-S-CN, W-S-CN, D-B-CN, S-B-CN, W-S-B-CN, -D-P-CN, W-D-

P-CN, -S-P-CN, W-S-P-CN. 设备带有 -S 后缀的没有显示，因

此需要一个外部显示设备。操作类似于对应的带有显示iso685

变形。

这本快速入门手册不能替代操作手册。你可以在我们的主页

www.bender.de/manuals 上找到操作手册。

m m

1 1 0

使用目的

ISOMETER® 监视不接地交直流主回路（IT 系统）的绝缘电阻，

主回路电压 AC, AC/DC 0...690 V 或 DC 0...1000 V。

出现在 AC/DC 系统中的直流组件不会影响操作特性。独立的电

源电压允许断开被监视系统。最大允许的系统泄露电容是1000

µF, 这取决于应用特定的配置。

安全介绍

电击危险 !

端子携带高电压并且直接接触端子可能会导致触

电

如果设备的端子直接连接到通电的 IT 系统 ,

。

危险

端子 E 和 KE 不必从 PE 线断开

由于安装不正确而导致损坏的风险 !

连接多个绝缘监视仪可能会导致安装损坏

如果连接超过一台绝缘监视仪，设备将不起作用，

并不会发出绝缘故障警报

警告

iso685_D00022_06_Q_CNEN/10.2016

1 0 8 m m

。

此外，

。

Insulation monitoring device

This quick-start guide applies to the following devices: iso685-D-

CN, W-D-CN, -S-CN, W-S-CN, D-B-CN, S-B-CN, W-S-B-CN, -D-P-CN,

W-D-P-CN, -S-P-CN, W-S-P-CN. Devices with the suffix -S do not

have a display and therefore need an external display. The opera-

tion is similar to the corresponding iso685 variants with display.

This quick-start guide does not replace the operating manual,

which can be found on our homepage under www.bender.de/

manuals.

R(an)

iso685(W)-D, iso685(W)-D-B-CN

PGH ON

Iso.Fehlersuche

43 s

iso685(W)-D-P-CN:

Intended use

The ISOMETER® monitors the insulation resistance of unearthed

AC/DC main circuits (IT systems) with mains voltages of AC, AC/

DC 0...690 V or DC 0...1000 V.

DC components existing in AC/DC systems do not influence the

operating characteristics. A separate supply voltage allows de-

energised systems to be monitored. The maximum permissible

system leakage capacitance is 1000 μF, dependent on the appli-

cation-specific profile.

Safety instructions

Risk of electric shock!

The terminals carry high voltage and direct contact with

these terminals will likely result in electrocution. If the

DANGER

terminals L1/+, L2, L3/- of the device are connected to a

live IT system, the terminals E and KE must not be

disconnected from the protective conductor (PE).

Risk of damage to property due to incorrect

installation!

Connecting more than one insulation monitoring de-

CAUTION

vice may result in damage to the installation. In addi-

tion, the device will not function and will not report an

insulation fault if more than one insulation monitoring

device is connected.

IT System

230 kΩ

40kΩ/10kΩ

IT-System

1/2

绝缘故障定位 /

insulation fault locati