Gage Bilt GB106 Series 원본 사용 설명서 - 페이지 11
{카테고리_이름} Gage Bilt GB106 Series에 대한 원본 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Gage Bilt GB106 Series 16 페이지. 16v battery installation tool
페이지 인쇄WARNING:
Only qualified and trained operators should install, adjust or use the installation power tool for all fasteners.
WARNING:
Operator
WARNING:
It is required that eye protection, hearing protection and safety boots be worn at all times while handling this equipment .
WARNING:
The users or the user's employer should assess specific risks that could be present before each use based on their applicatio n.
●
Be sure there is adequate clearance for tool and operator's hands before proceeding. Keep fingers clear of
any moving parts. Keep fingers clear from fasteners and installed materials. Severe personal injury may result.
●
Ensure that there are no electrical cables, gas pipes, etc., which can cause a hazard if damaged by the tool
WARNING:
Do not pull fastener in the air. Personal injury from fastener ejecting may occur.
WARNING:
Do not use as a hammer. If improperly used or damaged, liquid can escape from the battery causing skin irritations
or burns. Wash with water or seek medical attention immediately if liquid gets into eyes or burns occur.
WARNING:
Do not use in explosive atmosphere.
WARNING:
Charge the batteries only in chargers recommended by the manufacturer. Risk of fire or explosion if batteries
used on non manufacturer chargers.
WARNING:
Use only the specified batteries in the tool. The use of other batteries could result in injury or fire.
WARNING:
Keep battery (VP1309), when not in use, away from paper clips, coins, keys, nails, screws, or other small metal
objects that could cause bridging of the contacts. A short circuit between the battery contact can cause burns or fire.
WARNING:
Never operate the installation tool without the mandrel collection bottle (VP1002) or cover cap (VP1321).
WARNING:
By-passing the safety switch is prohibited. Do not use if switch is defective or can no longer be turned on or off.
WARNING:
Do not use cover cap (VP1321) with non self releasing nose assemblies. Damage to tool will occur.
WARNING:
Ensure the mandrel collection bottle (VP1002) / cover cap (VP1321) are properly connected and used correctly.
WARNING:
Avoid inadvertent starting of the installation tool.
WARNING:
Having your finger on the actuator assy (VP1316) while carrying the installation tool can lead to accidents.
CAUTION:
Check that the hanger clip (VP1322) is securely fitted before using the tool. Ensure the clip is not stretched too
far apart and loses its tension.
CAUTION:
Do not use beyond the design intent.
CAUTION:
Remove the battery (VP1309) before making adjustments to the tool, changing accessories, or putting tool away.
This precautionary measure prevents any unintentional starting of the installation tool.
Working with the Installation tool (GB106):
1.
Insert the mandrel of the fastener into the nose assembly.
Note: Tool will not function without the mandrel collection bottle (VP1002) or cover cap (VP1321) attached.
2.
Now insert the fastener into the parts to be fastened. For a good fastening result, ensure that the parts and head of the fastener
are resting on one another without a gap.
3.
Press the actuator assy (VP1316) until the mandrel is sheared.
4.
Hold the installation tool so that the mandrel collection bottle (VP1002) is facing downwards to ensure that the sheared mandrel
drops into the mandrel collection bottle (VP1002).
5.
When working with the cover cap (VP1321), hold the installation tool with the nose assy facing downwards after each set fastener
to ensure that the sheared mandrel drops out of the installation tool to the front. DO NOT use cover cap (VP1321) with non self
releasing nose assemblies. This would result in damage to the tool.
1.
Insert fastener into workpiece.
2.
Insert fastener into nose assembly.
3.
Press actuator to start cycle.
4.
Release actuator as soon as fastener breaks.
5.
Repeat steps 1-4.
GB106 16V BATTERY INSTALLATION TOOL SN: 1067 AND ABOVE
PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.
HOW TO USE THE GB106
MUST
read and understand all warnings and cautions.
Blind Fasteners
Images may not reflect actual tool or fastener
11
.
7/21 REV 8/21