Gage Bilt GB743SRVT 설치 도구 정보 - 페이지 4

{카테고리_이름} Gage Bilt GB743SRVT에 대한 설치 도구 정보을 온라인으로 검색하거나 PDF를 다운로드하세요. Gage Bilt GB743SRVT 13 페이지.

페이지 인쇄

DESCRIPTION

The GB743SRVT is a pneumatic-hydraulic split handle riveter designed specifically for the efficient installation of a

wide range of blind rivets. This tool's unique "split" system provides the operator with a lightweight ergonomic tool.

The handle and head assembly when held in hand weighs just 2.25 lbs (.80 kg)! The entire split handle riveter weighs

7 1/4 lbs. (3.29kg) It has a .900" (22.86mm) rivet setting stroke.

The GB743SRVT split handle riveter operates on a wide range of air pressure, with 90 to 100 psi. (6.2-6.9 bar) provid-

ing maximum efficiency. At 90 psi. (6.2 bar) air pressure, the GB743SRVT does not exceed 81.5 dB (A) and consumes

3 cfm at 20 cycles per minute.

The GB743SRVT comes with 3 feet of hose and a vacuum system, please consult our engineering department for spe-

cific applications.

The air inlet has a 1/4-18 female pipe threads for accepting the user's air hose fitting.

THE GB743SRVT IS ORDERED RIVET SPECIFIC. TO CHANGE TOOL OVER TO INSTALL OTHER RIVETS, SEE

CHARTS ON PAGES 10 & 11 FOR PART NUMBERS.

UNLESS ORDERED RIVET SPECIFIC (I.E. GB743SR/8N), THE STANDARD GB743SRVT IS FURNISHED WITH NOSE ASSEM-

BLY 8N-743-24 AND A SPARE NOSE TIP 10204 TO CONVERT TO A 6N-743-24. ALL OTHER NOSE TIPS MUST BE ORDERED

SEPARATELY. WHEN ORDERING TOOL RIVET SPECIFIC, PLEASE CONTACT GAGE BILT FOR MORE INFORMATION.

MAINTENANCE

WARNING:

Excessive contact with hydraulic oil and lubricants should be avoided.

WARNING:

Maintenance personnel

The performance of any tool depends upon good maintenance practices. Following these minimal requirements for

service and care will extend the life of your tool.

*Only use an air supply set at 90-100 psi (6.2-6.9 bar) equipped with a filter-regulator to prevent wear.

*The tool will eventually lose some hydraulic oil. Keep the hydraulic system full and free of air by

using the air bleeder ass'y (704153) on a regular basis.

*Proper care by operator is necessary in maintaining full productivity and reducing downtime. Read all

applicable tool manuals and nose assembly data sheets prior to operating tools.

*Keep nose assemblies, especially jaws, clean and free of chips and debris. Lube jaws and collet

surfaces that jaws ride on with light machine oil.

*Check daily all Hoses, Couplings, and Tools for damage or air/hydraulic leaks. Tighten or replace (if necessary).

*For a complete overhaul, tool kit GB704TK is recommended.

HYDRAULIC THREAD PREPARATION

IMPORTANT

Be sure to use thread sealant on all hydraulic fittings, Loctite® 30534 or similar Teflon®

infused pipe dope is recommended.

however, if it not properly applied, pieces may enter the hydraulic system and cause

malfunction and damage. Use 1 1/2 wraps of tape on each thread. Cut off all loose tape ends.

Tighten until fitting feels snug and then go 1/2 to a full turn past that point.

CAUTION:

CLEANING AND LUBRICATING PROCEDURE

Daily cleaning and lubrication of nose assembly will greatly reduce

downtime and increase life of components. Using sewing machine

oil, or an equivalent cleaner/lubricant, follow instructions below.

1. Disconnect tool vacuum line (if equipped).

2. Point nose assembly into oil as shown (Fig. A).

3. Cycle tool 8-10 times and wipe dry.

TORQUE SPECIFICATIONS

Socket Head Cap Screws (400061 and 400066) = 40 inch lbs.

Button Head Cap Screws (A-928) = 40 inch lbs.

Packing Plug (744118) = 45 foot lbs.

Flexlock Nut (400559) = 40 inch lbs.

End Cap (743214-1) = 45 foot lbs.

Button Head Cap Screws (402482) = 35-40 inch lbs. (Do NOT over-tighten)

S/N: 1070 AND ABOVE

PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

MUST

Over tightening can easily distort the threads.

read and understand all warnings and cautions.

CAUTION:

Teflon tape is an excellent thread sealer,

Image may not reflect

actual tool

REV. 7/14