Gage Bilt GB752SR 사용자 설명서 - 페이지 6

{카테고리_이름} Gage Bilt GB752SR에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Gage Bilt GB752SR 13 페이지. Installation tool

페이지 인쇄

DESCRIPTION

WARNING:

The balance of this tool is designed for vertical use and is not ergonomically best suited

for all applications. Gage Bilt will be pleased to advise for your specific application.

The GB752SR is a pneumatic-hydraulic split handle riveter designed specifically for the efficient installation

of a wide range of blind rivets. This tool's unique "split" system provides the operator with a lightweight

ergonomic tool. The handle and head assembly when held in hand weighs just 2.00 lbs! (.91kg) The entire

split handle riveter weighs 7.00 lbs. (3.18 kg). It has a .500 (12.7 mm) rivet setting stroke.

The GB752SR split handle riveter operates on a wide range of air pressure, with 90 to 100 psi. (6.2-6.9 bar)

providing maximum efficiency. At 90 psi. (6.2 bar) air pressure, the GB752SR does not exceed 81.5 db (A) and

consumes 3 cfm at 20 cycles per minute.

The GB752SR comes with 3 feet of hose. Hoses can be attached in the top rear or the bottom of the

split handle depending on the application. Vacuum systems are available for this tool, please consult our

engineering department for specific applications.

The air inlet has a 1/4-18 female pipe threads for accepting the user's air hose fitting.

NOSE ASSEMBLIES ARE NOT FURNISHED WITH THIS TOOL AND MUST BE ORDERED SEPARATELY.

MAINTENANCE

WARNING:

Excessive contact with hydraulic fluid and lubricants should be avoided.

WARNING:

Maintenance personnel

The performance of any tool depends upon good maintenance practices. Following these minimal

requirements for service and care will extend the life of your tool.

*Only use an air supply set at 90-100 psi. (6.2-6.9 bar) equipped with a filter-regulator to prevent wear.

*The tool will eventually lose some hydraulic oil. Keep the hydraulic system full (only use Dexron III, or

equivalent) and free of air by using the air bleeder ass'y (704153 &745163) on a regular basis.

*Proper care by operator is necessary in maintaining full productivity and reducing downtime. Read all

applicable tool manuals and nose assembly data sheets prior to operating tools.

*Keep nose assemblies, especially jaws, clean and free of chips and debris.

*All Screwed End Caps, Base Covers, Air Fittings, Actuator, Screws and Nose Assemblies are to be examined at

the end of each working shift to check that they are secure.

*Check tool, all hoses and all couplings daily for damage or air/hydraulic leaks. Tighten or replace (if necessary).

*For a complete overhaul, tool kit GB740TK is recommended.

HYDRAULIC THREAD PREPARATION

IMPORTANT:

Be sure to use thread sealant on all hydraulic fittings, Loctite® 30534 or similar Teflon® infused pipe

dope is recommended.

properly applied, pieces of Teflon may enter the hydraulic system and cause malfunction or damage.

Use 1 1/2 wraps of tape on each thread. Cut off all loose tape ends. Tighten until fitting feels snug and

then go 1/2 to a full turn past that point.

CLEANING AND LUBRICATING PROCEDURE

Daily cleaning and lubrication of nose assembly will greatly reduce

downtime and increase life of components. Using sewing machine oil, or

an equivalent cleaner/lubricant, follow instructions below.

1. Disconnect tool vacuum line (if equipped).

2. Point nose assembly into oil as shown.

3. Cycle tool 8-10 times and wipe dry.

TORQUE SPECIFICATIONS

Socket Head Cap Screws (400061 and 400066) = 40 inch lbs.

Button Head Cap Screws (A-928) = 40 inch lbs.

Packing Plug (704118) = 45 foot lbs.

Flexlock Nut (400559) = 40 inch lbs.

End Cap (752313) = 45 foot lbs.

Button Head Cap Screws (402482) = 35-40 inch lbs. (Do NOT over-tighten)

MUST

read and understand all warnings and cautions.

CAUTION:

Teflon tape is an excellent thread sealer, however, if it is not

CAUTION:

Over tightening can easily distort the threads.

Image may not

reflect actual tool

REV. 2/14