Dawn 5036 조립 및 작동 매뉴얼 - 페이지 9

{카테고리_이름} Dawn 5036에 대한 조립 및 작동 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Dawn 5036 19 페이지.

페이지 인쇄

HITCHING (8.1)

When you have thoroughly prepared your tractor and

toolbar, you are ready to hook-up. There are a wide

variety of hitch configurations, and it is recommended

that you familiarize yourself with the operation of your

hitch. Operational instructions for your hitch type

should be found in the users manual of both your

tractor and toolbar.

3-POINT HITCH (8.1.a)

Most 3-point hitches will be either Category 2 or

Category 3 hitches. If you have a category 2 hitch,

make sure that your toplink pin is 1" dia. and your lift

arm pins are 1 1/8" dia.. If you have a category 3

hitch, make sure that your toplink pin is 1 1/4" dia. and

your lift arm pins are 1 7/16" dia.. In some cases you

will have to remove, or relocate the tractor drawbar.

If the lift arm is equipped with an extension, release

the lock and pull the extension out its full length of

travel. Slowly back the tractor up to the toolbar until

the lift arms are aligned with the lower hitch pins.

Raise or lower the lift arms until the eyelets are

concentric with the lower hitch pins. Stop your tractor

and engage the parking brake to prevent rolling when

pinning the lift arms to the hitch. Pin each lift arm in

place and install a spring clip. Restart the tractor and

slowly raise the lift arms until the eyelet of the upper

link is concentric with upper hitch pin. Once again

stop the tractor and engage the parking brake. You

may have to lengthen or shorten the upper link to

install the hitch pin. After installing the upper hitch pin,

make sure to secure it with a spring clip. If you have a

"quickhitch" variety 3-point hitch, as before slowly

back up to the toolbar until the lower clasps of the

quick-hitch rest below the lower hitch pins. Lengthen

or shorten the upper link to align the quick hitch with

the hitch pins. Raise the quick-hitch until it engages

the hitch pins. Make sure the hitch retainers are

lowered, and engaged.

Tractor / Toolbar Connections

DRAWN HITCH (8.1.b)

Slowly back up the tractor to the toolbar until the

tractor drawbar is near the clevis of the toolbar. Stop

your tractor and engage the parking brake. Use the

toolbar jack to align the clevis with the tractor drawbar.

You may have to reposition the clevis. The lower hitch

panel of the clevis should be approximately 14 in.

above ground level, so that the upper hitch panel rides

abutting the tractor drawbar. Most toolbars have

optional settings for the clevis. Once the height of the

clevis is aligned with the tractor drawbar, slowly back

the tractor until the pin holes of the clevis and drawbar

are aligned. If you are using assistance in hitching the

toolbar, please make sure no person is between the

tractor and the toolbar when in motion.

WARNING!:

Tractors in motion may behave

erratically! Persons caught between a tractor in

motion and an agricultural implement could suffer

serious injury or death.

When you have aligned the pin holes, install the

appropriate pin and secure it with a spring clip. Your

toolbar should be equipped with safety chains. Make

sure to connect the safety chains before moving the

toolbar.

HYDRAULIC CONNECTIONS (8.2)

Shut off tractor and remote cylinder

WARNING!:

controllers that are in operation before attaching or

detaching hydraulic hoses to avoid potential injury

from hydraulic fluid escaping under pressure.

Ensure that all hoses and fittings are secure before

pressurizing system. Refer to installation guides for

proper assembly. All agricultural implements

equipped with hydraulic components should be

accompanied by a users manual that details attaching

and detaching. Please carefully follow the instructions

provided by the manufacturer.

ELECTRICAL CONNECTIONS (8.3)

Check to ensure that electrical connections are

secure and properly connected. Familiarize yourself

with the users manual of any electrical components

that your strip-till/fertilizer system might employ.

Carefully read the connection procedure found in the

users manual of that components manufacturer.

www.dawnequipment.com

Toll Free: 800.554.0007

Fax:815.899.3663