Dyna-Glo WK95C6R 소유자 매뉴얼 - 페이지 6

{카테고리_이름} Dyna-Glo WK95C6R에 대한 소유자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Dyna-Glo WK95C6R 18 페이지. Portable kerosene-heater

NEVER LEAVE THE HEATER

UNATTENDED WHILE BURNING!

It is normal for a kerosene heater to give off a slight odor upon start-up and shut-down.

After 5-10 minutes of operation, the heater should have reached its normal operating temperature and any

odor should be very slight.

NEVER store kerosene in direct sunlight or near a source of heat.

NEVER use kerosene that has been stored from one season to the next.

Kerosene deteriorates over time. "OLD KEROSENE" WILL NOT BURN PROPERLY IN

THIS HEATER.

A variety of problems can result from using poor quality kerosene --- smoke, odor, low flame, difficult ignition,

difficult shut-down, flame flickers and dies, excessive burning down of the wick, reduced wick life, wick

adjuster sticking, excessive deposits on the wick, etc.. If you encounter any of the problems listed above,

check your kerosene. If you discover that the kerosene is the problem, get a fresh supply of WATER-CLEAR

1-K KEROSENE OR RED DYED 1-K KEROSENE before using your heater again.

FUELING YOUR HEATER

NEVER FILL THE HEATER FUEL TANK IN THE LIVING SPACE:

FILL THE TANK OUTDOORS.

Before fueling the heater, take the heater, the kerosene, and the manual

siphon pump outdoors. To use the manual siphon pump, tighten the cap

on the top of the siphon, place the straight tube into the kerosene

container, and insert the flexible tube into the opening of the fuel tank. By

squeezing the bulb of the siphon pump, fuel will be transferred from the

kerosene container into the heater tank (Fig.10). Carefully watch the fuel

gauge on the base of the heater so that you will know when the tank is

getting full. When you approach the full mark, loosen the cap on top of the

siphon pump. This will stop the flow of kerosene. DO NOT OVERFILL

YOUR HEATER. Allow the siphon pump to drain thoroughly before you

remove it from the tank and the kerosene container.

After fueling the fuel tank of the heater by using siphon pump, make sure

that you loosen (counter clock wise) the cap on the siphon pump to drain

throughly the remaining kerosene in the siphon pump. For the reuse of siphon pump, make sure that you

tighten (clock wise) the cap on the siphon pump to transfer the kerosene into the fuel tank properly. (Fig.11)

IMPORTANT NOTICE REGARDING FUELING OF THE HEATER : When fueling your heater for the first

time and any other time when the tank has been completely empty, as in "Dry Burning" (page 8) make sure

to allow the wick to soak a minimum 60 minutes before you attempt to light the heater. Take note of the

time you started to soak the wick or use a kitchen timer or wrist watch with an alarm feature. Failure to

properly soak the wick can trap air pockets in the wick causing the heater to burn poorly.

Premature ignition can destroy your wick.

IMPORTANT NOTICE REGARDING FIRST IGNITION OF HEATER

The first time you light your heater there may be some odor due to the burning off of oils used in the

manufacturing process. To avoid this you may wish to burn the heater outside on a calm and windless day.

If it s windy consider a porch or garage or other room where the windows can be open to disperse the odor.

Fig.10

LOOSEN

TIGHTEN

Fig.11