Dynabrade Dynorbital-Spirit 21065 운영 및 유지보수 매뉴얼 - 페이지 5
{카테고리_이름} Dynabrade Dynorbital-Spirit 21065에 대한 운영 및 유지보수 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Dynabrade Dynorbital-Spirit 21065 13 페이지. 12,000 rpm air powered random orbital sander
Dynabrade Dynorbital-Spirit 21065에 대해서도 마찬가지입니다: 운영 및 유지보수 지침 매뉴얼 (8 페이지), 매뉴얼 (13 페이지)
페이지 인쇄
Central Vacuum/Machine Exhaust
7
Non-Vacuum to Vacuum Conversion Kits
Original
Converts
Non-Vac Tool
to
3-1/2" (89mm)
Self-Generated Vac-Ready
3-1/2" (89mm)
Central Vac-Ready
5" (127mm)
Self-Generated Vac-Ready
5" (127mm)
Central Vac-Ready
6" (152mm)
Self-Generated Vac-Ready
6" (152mm)
Central Vac-Ready
To Disassemble:
1. Disconnect tool from power source. Invert machine and secure in vise, using 57092 Collar (supplied in 57098 Repair Kit) or padded jaws.
2. Remove sanding pad with 50679 (26mm) Open-End Wrench (supplied with sander) and lip-seal shroud from housing.
3. Remove 56028 Muffler Cap and 56027 Muffler Insert (2) from 57066 Muffler Body. Using a 12mm hex wrench (supplied in 57098 Repair Kit), remove
muffler body from housing (not applicable for Self-Generated Vac to Central Vac).
Non-Vac to Self-Generated Vac for Hook-Up to Self-Contained Dust Collection System
1. Attach 57083 Vacuum Adapter to either 57084, 57086, 57087 Vacuum Overskirts or 57089 Vacuum Lip-Seal Shroud. Then attach to the housing making
sure the protrusions on the overskirt or shroud are aligned with the notches on the housing.
2. Place 95526 O-Ring on the muffler body between the shoulder and the four (4) protrusions. Using a 12mm hex wrench, attach the muffler body and
o-ring to the housing through the vacuum adapter.
3. Place vacuum nozzle into the vacuum adapter with the slots facing outward making sure that the knob on the nozzle is aligned with the slot in the adapter.
4. Place 57067 Vacuum Tube into the vacuum adapter with the grooves facing inward until the adapter "snaps" onto the tube and the tube cannot be pulled
out. If the tube can be pulled out, rotate it 1/4 turn and place it back into the adapter until it "snaps".
5. Rotate tube until holes line up. Insert dowel pin in holes until it is centered. Attach sanding pad, attach machine to portable dust collection system.
Non-Vac to Central Vac
1. Attach 57093 Vacuum Adapter to either 57084, 57086, 57087 Vacuum Overskirts or 57089 Vacuum Lip-Seal Shroud. Then attach to the housing making
sure the protrusions on the overskirt or shroud are aligned with the notches on the housing.
2. Using a 12mm hex wrench, attach the muffler body to the housing through the central vacuum adapter.
3. Place muffler cap with inserts on muffler body making sure that the protrusions on the body fit in the pockets on the cap.
4. Attach weight-mated vacuum sanding pad with 50679 (26mm) Open-End Wrench. Attach machine to central vacuum system.
Self-Generated Vac to Central Vac
1. Remove 96197 Dowel Pin with an 1/8" drive pin. Remove 57067 Vacuum Tube from 57083 Vacuum Adapter by turning it clockwise while pulling backward.
2. Using a small flat screwdriver, pry vacuum nozzle until it is loose and then remove it by using two fingers to push and pull it until it hits the "legs" on
vacuum adapter. Place vacuum tube back into vacuum adapter far enough to push the "legs" back, then push vacuum nozzle and vacuum tube
out the rest of way.
3. Using a 12mm hex wrench (supplied in 57098 Repair Kit), remove the 57066 Muffler Body and 95526 O-Ring from the housing through the adapter.
Remove the o-ring from the muffler body.
4. Remove 57083 Vacuum Adapter and attach 57093 Vacuum Adapter to either 57084, 57086, 57087 Vacuum Overskirts or 57089 Vacuum Lip-Seal Shroud.
Then attach to the housing making sure that the protrusions on the overskirt or shroud are aligned with the notches on the housing.
5. Using a 12mm hex wrench, attach the muffler body and o-ring to the housing through the central vacuum adapter.
6. Place muffler cap with inserts on muffler body making sure that the protrusions on the body fit in the pockets on the cap. Attach sanding pad.
Central Vac to Self Generated Vac
1. Remove 57093 Central Vacuum Adapter and put the 57083 Vacuum Adapter in its place.
Machine Exhaust Assemblies
Self Generated Vacuum (Vac-Ready)/Machine Exhaust
1
2
3
8
9
Kit
Part Number
57118
57119
57120
57121
57122
57123
Vacuum Conversion
(continued on next page)
3
4
5
Non-Vacuum/Machine Exhaust
Index Key
No.
Part #
Description
1 57083 Vacuum Adapter
2 96197 Dowel Pin
3 57066 Muffler Body
4 95526 O-Ring
5 59088 Vac Nozzle
Optional: 30 quantity Muffler Insert available, P/N 56054.
Instructions..
6
3
8
9
10
6 57067 Vac Tube
7 57093 Vacuum Adapter
8 56027 Muffler Insert (2)
9 56028 Muffler Cap
10 59273 Muffler Assembly