Dynabrade Dynorbital-Spirit 59108 안전, 운영 및 유지보수

{카테고리_이름} Dynabrade Dynorbital-Spirit 59108에 대한 안전, 운영 및 유지보수을 온라인으로 검색하거나 PDF를 다운로드하세요. Dynabrade Dynorbital-Spirit 59108 13 페이지. 12,000 rpm random orbital sander
Dynabrade Dynorbital-Spirit 59108에 대해서도 마찬가지입니다: 안전, 운영 및 유지보수 (4 페이지), 안전, 운영 및 유지보수 (8 페이지)

페이지 인쇄

Dynorbital-Spirit

Models:

3/8" Orbit

3/16" Orbit

59000 59010

59015 59025

59001 59011

59016 59026

59002 59012

59017 59027

59003 59013

59018 59028

59004 59014

59019 59029

59005 59100

59020 59105

59006 59101

59021 59106

59007 59102

59022 59107

59008 59103

59023 59108

59009 59104

59024 59109

FOR COMPLETE MODEL DESCRIPTION REFERENCE PAGE 6.

Read and understand this tool manual before operating your air tool. Follow all safety rules for the protection of operating person-

nel as well as adjacent areas. Always operate, inspect and maintain this tool in accordance with the American National Safety

Institute (ANSI) Safety Code for Portable Air Tools – B186.1. For additional safety information, refer to Safety Requirements for the

Use, Care and Protection of Abrasive Wheels – ANSI B7.1, Code of Federal Regulation – CFR 29 Part 1910, European Committee for

Standards (EN) Hand Held Non-Electric Power Tools – Safety Requirements and applicable State and Local Regulations.

Read and understand tool manual before

work starts to reduce risk of injury to

operator, visitors, and tool.

Eye protection must be worn at all times,

eye protection to conform to ANSI Z87.1.

Respiratory protection to be used when exposed to

contaminants that exceed the applicable threshold

limit values required by law.

Carefully Read all instructions before operating or servicing any Dynabrade

Products offered by Dynabrade are not to be modified, converted or otherwise alerted from the original design without expressed written consent from Dynabrade, Inc.

Tool Intent: Dynorbital-Spirit™ Random Orbital Sander is used for sanding and finishing a variety of materials including wood, metal, plastic, fiberglass, solid surfaces,

composites, rubber, glass and stone.

Training: Proper care, maintenance, and storage of your tool will maximize its performance.

• Employer's Responsibility – Provide Dynorbital-Spirit™ operators with safety instructions and training for safe use of tools and accessories.

Accessory Selection:

• Abrasive/accessory RPM (speed) rating MUST be approved for AT LEAST the tool RPM rating.

• Before mounting an accessory, visually inspect for defects. Do not use defective accessories.

• Follow tool specifications before choosing size and type of accessory.

• Only use recommended fittings and air line sizes. Air supply hoses and air hose assemblies must have a minimum working pressure rating of 150 PSIG (10 bars, g) or 150

percent of the maximum pressure produced in the system, whichever is higher. (See Tool Machine Specifications Table.)

• DO NOT use – ......................................................

Warning: Always wear eye protection. Operator of tool is responsible for following: accepted eye, face, respiratory, hearing and body protection.

Caution: Hand, wrist and arm injury may result from repetitive work, motion and overexposure to vibration.

Air Tool Manual – Safety, Operation and Maintenance

SAVE THIS DOCUMENT, EDUCATE ALL PERSONNEL

3/32" Orbit

59030 59040

59031 59041

59032 59042

59033 59043

59034 59044

59035 59110

59036 59111

59037 59112

59038 59113

59039 59114

WARNING

SAFETY LEGEND

WARNING

SAFETY INSTRUCTIONS

Do Not Use Tool For Anything Other Than Its Intended Applications.

OPERATING INSTRUCTIONS

(Continued on next page.)

™

12,000 RPM Air Powered Random Orbital Sander

Practice safety requirements. Work alert,

have proper attire, and do not operate tools under

the influence of alcohol or drugs.

Ear protection to be worn when exposure to sound,

exceeds the limits of applicable Federal, State or

local statues, ordinances and/or regulations.

Air line hazard, pressurized supply lines and flexible

hoses can cause serious injury. Do not use dam-

aged, frayed or deteriorated air hoses and fittings.

Abrasive Power Tool.

Parts Page Reorder No. PD02•10U

Effective February, 2002

WARNING