Dynabrade 40250 안전, 운영 및 유지보수 매뉴얼 - 페이지 4

{카테고리_이름} Dynabrade 40250에 대한 안전, 운영 및 유지보수 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Dynabrade 40250 4 페이지. Right angle grinder

페이지 인쇄
Type 27 Flanged Wheel (7/8" Dia. Arbor Hole)
1. With power source disconnected from the tool.
2. Clean spindle and flange mounting surfaces. Inspect for nicks, cuts and sharp edges.
3. Install drive flange with raised boss facing outward. Engage bottom flange slot and spindle flats.
4. Check for flange flatness and runout by rotating spindle and drive flange together.
5. Install Type 27 grinding wheel over spindle thread and over raised boss on flange.
6. With 1/4" thick wheels & greater, install outer flange nut with raised boss facing toward abrasive wheel,
engage spindle lock and secure flange firmly against wheel. (See fig. 1)
7. With 1/8" thick wheels & less, install outer flange nut with raised boss facing away from abrasive wheel,
engage spindle lock and secure flange firmly against wheel. (See fig. 2)
8. Check for wheel firmness by holding the spindle and pulling on the edge of the wheel in the
tightening direction.
Caution: Over tightening the outer flange nut can cause damage to the wheel and/or flanges.
• Use only Dynabrade flanges: 89310 & 89356 Flanges.
Type 27 Hubbed Wheel (5/8"-11 Internal Affixed Flange)
1. With power source disconnected from the tool.
2. Some TYPE 27 grinding wheels come equipped with a disposable flange affixed to them. For use of this
type wheel store both the driving flange and the outer flange nut provided with the tool for future use.
3. Engage spindle lock and thread grinding wheel to tool securely.
4. Visually inspect the grinding surface face relationship to the bend of the lip on the guard.
5. ONLY USE grinding wheel whose face of the wheel is behind bend of lip on guard. (See fig. 3)
Following the reasonable assumption that any inherent defect which might prevail in a product will become apparent to the user within one year from the date of purchase,
all equipment of our manufacture is warranted against defects in workmanship and materials under normal use and service. We shall repair or replace at our factory, any
equipment or part thereof which shall, within one year after delivery to the original purchaser, indicate upon our examination to have been defective. Our obligation is con-
tingent upon proper use of Dynabrade tools in accordance with factory recommendations, instructions and safety practices. It shall not apply to equipment which has been
subject to misuse, negligence, accident or tampering in any way so as to affect its normal performance. Normally wearable parts such as bearings, brushes, gears, etc.,
are not covered under this warranty.
Model
Motor
Number
RPM
40250
10,000

Wiring Diagram

AC 120V ~ 60Hz
Switch
Reference Contact Information
1. CSA International
8501 East Pleasant Valley Road
Cleveland, Ohio 4431-5575
Tel: 1 (216) 524-4990
Fax: 1 (216) 642-3463
Visit Our Web Site: www.dynabrade.com
DYNABRADE, INC., 8989 Sheridan Drive • Clarence, NY 14031-1490 • Phone: (716) 631-0100 • Fax: 716-631-2073 • International Fax: 716-631-2524
DYNABRADE EUROPE S.àr.l.,
© DYNABRADE, INC., 2008
Wheel Mounting Instructions
One Year Warranty

Machine Specifications

Pad Diameter
Inch (mm)
Voltage
5 (127)/4-1/2 (114)
120 V (AC)
Stator
2. Government Printing Office – GPO
Superintendent of Documents
Attn. New Orders
P.O. Box 371954
Pittsburgh, PA 15250-7954
Tel: 1 (202) 512-1803
Zone Artisanale • L-5485 Wormeldange—Haut, Luxembourg • Telephone: 352 76 84 94 1 • Fax: 352 76 84 95 1
Side View
Right Angle Housing
Driving Flange
Spindle
Outer Flange Nut
Fig. 1
Outer Flange Nut
Fig. 3
Side View
Right Angle Housing
Current
Phase
Frequency
7.5 Amps
1
60 Hz

Optional Accessories

FIND THE MOST CURRENT OFFERING OF ACCESSORIES AND
SUPPORT DOCUMENTS @ WWW.DYNABRADE.COM
Rotor
Fig. 2
1/4"
Outer Flange Nut
Face of Wheel must be behind bend of lip.
Weight
Length
Pound (kg)
Inch (mm)
5.2 (2.4)
13.5 (343)
95542 Grease 10 oz.
•
High film strength; excellent
resistance to water, steam, etc.
•
Workable range 0˚ F to 300˚ F.
DYNABRADE
Safety Guard
Wheel
1/8"
Safety Guard
Wheel
Bend of Lip
Height
Inch (mm)
3.5 (89)
®
PRINTED IN USA