Dynabrade 52683 안전, 운영 및 유지보수 매뉴얼

{카테고리_이름} Dynabrade 52683에 대한 안전, 운영 및 유지보수 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Dynabrade 52683 8 페이지. 1hp die grinder

페이지 인쇄

1Hp Die Grinder

Governor Controlled

Models:

52660 – 950 RPM, 1/4"

52661 – 1,800 RPM, 1/4"

52662 – 3,400 RPM, 1/4"

52663 – 4,500 RPM, 1/4"

52680 – 950 RPM, 6mm

52681 – 1,800 RPM, 6mm

52682 – 3,400 RPM, 6mm

52683 – 4,500 RPM, 6mm

Read and understand this tool manual before operating your air tool. Follow all safety rules for the protection of operating personnel

as well as adjacent areas. Always operate, inspect and maintain this tool in accordance with the American National Safety Institute

(ANSI) Safety Code for Portable Air Tools – B186.1. For additional safety information, refer to Safety Requirements for the Use, Care

and Protection of Abrasive Wheels – ANSI B7.1, Code of Federal Regulation – CFR 29 Part 1910, European Committee for Standards

(EN) Hand Held Non-Electric Power Tools – Safety Requirements and applicable State and Local Regulations.

Read and understand tool manual before

work starts to reduce risk of injury to

operator, visitors, and tool.

Eye protection must be worn at all times,

eye protection to conform to ANSI Z87.1.

Respiratory protection to be used when exposed to

contaminants that exceed the applicable threshold

limit values required by law.

Carefully Read all instructions before operating or servicing any Dynabrade

Products offered by Dynabrade are not to be modified, converted or otherwise altered from the original design without expressed written consent from Dynabrade, Inc.

Tool Intent: Planetary geared die grinders are ideal for removal and polishing of materials using deburring, cleaning and polishing accessories.

This power tool is not intended for use in potentially explosive atmospheres and is not insulated against contact with electrical power.

Training: Proper care, maintenance, and storage of your tool will maximize its performance.

• Employer's Responsibility – Provide planetary geared die grinder operators with safety instructions and training for safe use of tools and accessories.

Accessory Selection:

• Abrasive/accessory RPM (speed) rating MUST be approved for AT LEAST the tool RPM rating.

• Before mounting an accessory, visually inspect for defects. Do not use defective accessories.

• Use only recommended accessories. See back page of manual and Dynabrade literature.

• Follow tool specifications before choosing size and type of accessory.

• Only use recommended fittings and air line sizes. Air supply hose and air hose accessories must have a minimum working pressure rating of 150 PSIG (10 Bars, g) or 150

percent of the maximum pressure produced in the system, whichever is higher. (See tool Machine Specifications table.)

• DO NOT use – cut off wheels or router bits.

Warning: Always wear eye protection. Operator of tool is responsible for following: accepted eye, face, respiratory, hearing and body protection.

Caution: Hand, wrist and arm injury may result from repetitive work, motion and overexposure to vibration.

Air Tool Manual – Safety, Operation and Maintenance

SAVE THIS DOCUMENT, EDUCATE ALL PERSONNEL

WARNING

SAFETY LEGEND

WARNING

SAFETY INSTRUCTIONS

Do Not Use Tool For Anything Other Than Its Intended Applications.

OPERATING INSTRUCTIONS

(continued on next page)

Practice safety requirements. Work alert,

have proper attire, and do not operate tools under

the influence of alcohol or drugs.

Ear protection to be worn when exposure to sound,

exceeds the limits of applicable Federal, State or

local statues, ordinances and/or regulations.

Air line hazard, pressurized supply lines and flexible

hoses can cause serious injury. Do not use damaged,

frayed or deteriorated air hoses and fittings.

Abrasive Power Tool.

Parts Page Reorder No. PD04•40

Effective August, 2004

WARNING