Dynabrade 13519 안전, 운영 및 유지보수 - 페이지 3
{카테고리_이름} Dynabrade 13519에 대한 안전, 운영 및 유지보수을 온라인으로 검색하거나 PDF를 다운로드하세요. Dynabrade 13519 9 페이지. 1 hp dynastraight 6" extension, governor controlled, 1,800/3,400/4,500/6,000 rpm with 5/8" or 1" combination arbor/with 1/2" diameter arbor, with 5/8"-11 threaded arbor
페이지 인쇄
Disassembly Instructions - 1hp Extension Dynastraight
Important: Manufacturer's warranty is void if tool is disassembled before warranty expires.
Disconnect tool from power source before tool repair.
Motor Disassembly:
1. Remove abrasive accessory and hardware from arbor/threaded spindle.
2. Using 51989 Repair Collar ( order separately ) or padded vise, secure front end of housing using machined flats on the silver ring.
3. Remove 51952 Extension Handle from 53695 Gear Casing (twist counterclockwise).
4. Slide 51982 Bearing Spacer and spindle assembly through rear of 51952 Extension Handle.
5. Remove 96524 Retaining Ring from front of extension handle if necessary.
6. Secure 51955 Spindle at wrench flats, and remove arbor/threaded spindle, 51956 Felt Ring and 51969 Coupling Nut.
7. Secure 01007 Bearing and press 51955 Spindle through both 01007 Bearings.
8. Secure 54520 Bearing and press 51955 through 54520 Bearing.
9. Remove 53695 Gear Casing (twist counterclockwise).
10. Secure planetary Carrier using 53698 Wrench ( order separately ) and remove 51969 Coupling Nut (twist counterclockwise).
11. Remove 04014 Set Screw(s) and pull planetary carrier assembly(s) from planetary gear casing.
12. Press planetary carrier assembly through 54520 Bearing.
13. Remove 96498 Wave Spring.
14. Remove ring gear and press retainer pins and gears from planetary carrier.
15. Remove remaining tool assembly from vise.
16. Pull motor assembly from housing assembly.
17. Remove governor assembly by using a slotted screw driver. (LEFT HAND thread)
18. Secure 51925 Cylinder and place a 1/8" (3mm) drift pin to the base of the internal thread and press the 51921 Rotor from the 02057 Rear Bearing.
19. Slide 02057 Rear Bearing from 51923 Rear Bearing Plate.
20. Remove 51925 Cylinder and 51926 Blades.
21. Press rotor through 54520 Bearing, 51922 Front Bearing Plate and 51927 Rotor Spacer.
22. Slide 54520 Bearing and shims from 51922 Front Bearing Plate.
Motor and Extension Disassembly Complete.
Housing Disassembly:
1. Secure housing using 51989 Repair Collar ( see back cover for Optional Accessories ).
2. Remove inlet bushing with muffler assembly (twist counterclockwise).
3. Remove 53682 Gasket, 51943 Spring, 96442 O-Ring, 51940 Spacer, 94528 Felt Silencer, 53686 Muffler Cap, 94924 Wave Spring and
53683 Spacer from 53681 Inlet Bushing.
4. Remove 51944 Tip Valve and 51945 Valve Seat.
Housing Disassembly Complete.
Assembly Instructions - 1hp Extension Dynastraight
Motor Assembly:
Important: Be sure parts are clean and in good repair before assembling. Follow grease, oil and torque specifications.
1. Place Rotor into padded vise with male thread or spline facing upwards.
2. Slip 51927 Rotor Spacer over rotor shaft and down against rotor body face.
3. Press 96441 Coiled Pin into 51922 Front Bearing Plate. Make certain, coiled pin does not protrude beyond internal bearing surface.
4. Place a .002" shim into the base of 51922 Front Bearing Plate as an initial spacing and slide 54520 Bearing to the front plate base. Note: 51951 Shim
Pack contains .001" and .002" shims.
5. Press bearing/bearing plate assembly onto rotor. (For 1,800, 3,400, & 4,500 RPM Models) Slide bearing/bearing plate onto rotor and thread pinion
into place. Torque to 17 N•m (For 6,000 RPM Model.)
6. Check clearance between rotor and front bearing plate by using a .001" feeler gauge. Clarence should be between .001" – .0015". Adjust clarence by
repeating steps 4 and 5 with different shims if necessary.
7. Once proper rotor gap clarence is achieved, install well lubricated 51926 Blades (4) into rotor slots. Dynabrade recommends lubricating blades with
95842 Air Lube. Important: Make certain beveled edge of blade follows rotor outside diameter.
8. Install 51925 Cylinder over rotor and front plate raised boss. Align coiled pin on front to cylinder slot.
9. Press 96441 Coiled Pin into blind hole on 51923 Rear Bearing Plate. Press (2) 96445 Coiled Pins into the back side of rear bearing plate.
10. Peel backing off 51924 Gasket and align it firmly in place onto 51923 Rear Bearing Plate.
11. Place 51923 Rear Bearing Plate over rotor mandrel and insert raised boss on rear bearing plate into cylinder diameter, while inserting short coiled pin
into cylinder slot. Be sure inlet slot on rear bearing plate line up with inlet slot on cylinder. Flip cylinder end to end and repeat step 8 for correct assembly.
12. Press 02057 Bearing onto rotor and onto 51923 Rear Bearing Plate until it is seated. Important: Cylinder must fit snug between bearing plates. If too
tight, rotor will not turn freely. Rotor must be lightly tapped at press fit end until rotor spins freely while still maintaining a snug fit. A loose fit will not
achieve the proper preload on motor bearing. While pressing 02057 Bearing, make certain to contact inner race of bearing only.
13. Add one drop of #243 Loctite
slotted screw head. Torque to 2 N•m (18 lb.-in.).
®
(or equiv.) to governor assembly male thread and screw governor assembly onto place (LEFT HAND thread) with a
(continued on next page)