GREAT PLANES ElectriFly PBY Catalina 사용 설명서 - 페이지 3

{카테고리_이름} GREAT PLANES ElectriFly PBY Catalina에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. GREAT PLANES ElectriFly PBY Catalina 20 페이지. Arf

페이지 인쇄

GREAT PLANES ElectriFly PBY Catalina 사용 설명서

PROTECT YOUR MODEL, YOURSELF

& OTHERS...FOLLOW THESE

IMPORTANT SAFETY PRECAUTIONS

1. Your PBY Catalina should not be considered a toy, but

rather a sophisticated, working model that functions very

much like a full-size airplane. Because of its performance

capabilities, the PBY Catalina, if not assembled and operated

correctly, could possibly cause injury to yourself or spectators

and damage to property.

2. You must assemble the model according to the instructions.

Do not alter or modify the model, as doing so may result in an

unsafe or unﬂ yable model. In a few cases the instructions may

differ slightly from the photos. In those instances the written

instructions should be considered as correct.

3. You must take time to build straight, true and strong.

4. You must use an R/C radio system that is in ﬁ rst-class

condition, and a correctly sized motor and components

throughout the building process.

5. You must correctly install all R/C and other components so

that the model operates correctly on the ground and in the air.

6. You must check the operation of the model before every

ﬂ ight to insure that all equipment is operating and that the

model has remained structurally sound. Be sure to check

clevises or other connectors often and replace them if they

show any signs of wear or fatigue.

7. If you are not an experienced pilot or have not ﬂ own

this type of model before, we recommend that you get the

assistance of an experienced pilot in your R/C club for

your ﬁ rst ﬂ ights. If you're not a member of a club, your local

hobby shop has information about clubs in your area whose

membership includes experienced pilots.

We, as the kit manufacturer, provide you with a top quality,

thoroughly tested kit and instructions, but ultimately the

quality and ﬂ yability of your ﬁ nished model depends

on how you build it; therefore, we cannot in any way

guarantee the performance of your completed model,

and no representations are expressed or implied as to

the performance or safety of your completed model.

Remember: Take your time and follow the instructions to

end up with a well-built model that is straight and true.

LITHIUM BATTERY

HANDLING & USAGE

WARNING!! Read the entire instruction sheet included with

the battery. Failure to follow all instructions could cause

permanent damage to the battery and its surroundings, and

cause bodily harm!

• ONLY use a LiPo approved charger. NEVER use a NiCd/

NiMH peak charger!

• NEVER charge in excess of 4.20V per cell.

• ONLY charge through the "charge" lead. NEVER charge

through the "discharge" lead.

• NEVER charge at currents greater than 1C.

• ALWAYS set charger's output volts to match battery volts.

• ALWAYS charge in a ﬁ reproof location.

• NEVER trickle charge.

• NEVER allow battery temperature to exceed 150° F (65° C).

• NEVER disassemble or modify pack wiring in any way or

puncture cells.

• NEVER discharge below 2.5V per cell.

• NEVER place on combustible materials or leave unattended

during charge or discharge.

• ALWAYS KEEP OUT OF REACH OF CHILDREN.

DECISIONS YOU MUST MAKE

This is a partial list of items required to ﬁ nish the PBY Catalina

that may require planning or decision making before starting

to build. Order numbers are provided in parentheses.

Radio Equipment

❏

4-Channel Radio (such as the Futaba

❏

Micro Receiver (If you choose to, a standard size receiver

will ﬁ t in the radio compartment)

❏

Two S3103 Micro-Mini Servos (FUTM0037) for the ailerons

(or an equivalent servo with 17 oz-in of torque and servo

case dimensions of 0.9" x 0.4" x 0.8" [22 x 11 x 20mm])

❏

Two S3110 Micro Servos (FUTM0046) for the elevator and

rudder (or an equivalent servo with 22 oz-in of torque and servo

case dimensions of 0.9" x 0.4" x 0.8" [22 x 11 x 20mm])

❏

Two 6" [150mm] Servo Extensions (HCAM2701 for Futaba)

❏

Two Servo Y-Harnesses (HCAM2751 for Futaba)

Motor, Speed Control and

Battery Recommendation

❏

Two RimFire Brushless 28-30-950 Motors (GPMG4560)

❏

Two ElectriFly SS-25 Speed Controls (GPMM1820)

❏

One Deans U Parallel ESC adapter (GPMM3141)

❏

ElectriFly Power Series Lithium Polymer Battery.

2100mAh 11.1 Volt (GPMP0617), 3200mAh 11.1 Volt

(GPMP0623) or equivalent

❏

ElectriFly PolyCharge

4EXA)

™

4 Battery Charger (GPMM3015)