2gig Technologies 2GIG-STVGRL1-345 설치 지침 - 페이지 2

{카테고리_이름} 2gig Technologies 2GIG-STVGRL1-345에 대한 설치 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. 2gig Technologies 2GIG-STVGRL1-345 2 페이지.

페이지 인쇄

2gig Technologies 2GIG-STVGRL1-345 설치 지침

Programming the Device on the GC2/GC3 Panel

For GC2 and GC3 panels, program the Stove & Grill Guard on your

2GIG panel with the following parameters. (Please refer to your

panel's quick programming guide for the actual steps.)

Sensor Type:

(23) No Response Type

Sensor Equipment Type: Contact

Equipment Code:

(0862) 2GIG Thin Door/Window Contact

Serial Number:

[Input the unique 7-digit TXID.]

Equipment Age:

New

Sensor Loop Number:

Dialer/Transmission Delay: Enabled

Voice Descriptor:

GAS LEFT ON

Sensor Reports:

Enabled

Sensor Supervised:

Disabled

Sensor Chime:

[User-speciﬁ ed]

This is a provisional Equipment Code. A new category called

"Stove & Grill Guard" (or similar name) will be added in a future

GC2/GC3 panel update.

Alterna vely, a Stove & Grill Guard can be automa cally learned in.

This is a recommended voice descriptor. The user may deﬁ ne a

custom voice descriptor, as needed.

Programming the Device on the Vario Panel

For the Vario panel, a er learning in

conﬁ gure the zone the Stove & Grill Guard is in with the following

parameters:

Zone Type:

Output Trigger

Zone Sound Armed Away: Silent

Zone Sound Armed Stay: Silent

Zone Sound Disarmed:

Chime or Silent

Alterna vely, you can use the Vario TXID to manually enroll the

device.

Programming the Device on the Honeywell Vista Panel

For the Honeywell Vista panel, ﬁ rst enroll the Stove & Grill Guard

into the panel as follows:

• For Panel 15P, 20P or 50P, auto-enroll the device into the panel.

The LED will ﬂ ash 6 mes to conﬁ rm the enrollment.

• For Panel 10SE or 20SE, set the address to "00", then auto-enroll.

The LED will be solid green to conﬁ rm the enrollment.

Then program the panel as follows:

1. Enter [4-digit installer code], then [800], then [*56]. When the

screen displays "Set to Conﬁ rm?" press [*] bu on.

2. When prompted by the screen to "Enter ZN Num" input a

chosen zone number (ZN) between 09 and 48, then press [*]

bu on.

3. Type in the ZN to display the current zone summary on the

screen.

4. Enter the following parameters:

• ZT (zone type): [10]

• P (par

on): [1]

• RC (report code): [01] then [0010]

• IN (input device type): [RF Trans. 3]

• Transmi er Serial Number: [A] then [7-digit TXID]

• Loop Number: [2]

5. Conﬁ rm the zone summary displays the parameters correctly.

Setting up E-mail Notification – Alarm.com Accounts Only

1. Navigate to h p://www.alarm.com and click LOGIN.

2. Your systems dashboard page will appear. Select the Security tab

and click Sensors.

3. Iden fy the new sensor you added. You can rename the

Sensor Name. When ﬁ nished, click Save.

4. Click the No ﬁ ca ons tab, and then +New No ﬁ ca on

bu on to create a new event. The menu will appear with

the Standard tab open by default.

5. Click Sensor Le Open. Add parameters. Also, click +Add

the Stove & Grill Guard, please

6. Click Close when names have been selected, then click Save

Speciﬁ cations

• Signal Range: 100 . open-air from a 2GIG panel

• Transmission Frequency: 345 MHz

• Disc dimensions: 2.2" diameter, 0.21" thickness

• Opera ng Temperature: 14°F to 167°F (-10°C to 75°C)

• Ba ery Life: Up to 5 years

FCC & IC Notice

This device complies with Part 15 of the FCC Rules and Industry Canada license

exempt standard(s). Opera on is subject to the following two condi ons:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference

received that may cause undesired opera on.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables

aux appareils radio exempts de licence. L'exploita on est autorisée aux deux

condi ons suivantes:

(1) l'appareil ne doit pas produire de brouillage, et

(2) l'u lisateur de l'appareil doit accepter tout brouillage radioélectrique subi,

même si le brouillage est suscep ble d'en comprome re le fonc onnement.

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du

Canada.

This equipment has been tested and found to comply with the limits for a Class

B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed

to provide reasonable protec on against harmful interference in a residen al

installa on.

This equipment generates, uses, and can radiate radio frequency energy and, if

not installed and used in accordance with the instruc ons may cause harmful

interference to radio communica ons. However, there is no guarantee that

interference will not occur in a par cular installa on. If this equipment does

cause harmful interference to radio or television recep on, which can be

determined by turning the equipment oﬀ and on, the user is encouraged to try

to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separa on between the equipment and receiver

• Connect the equipment into an outlet on a circuit diﬀ erent from that to

• Consult the dealer or an experienced radio/TV technician to help

WARNINGS:

• Changes or modiﬁ ca ons not expressly approved by the manufacturer could

• The Stove & Grill Guard is not intended as a life-safety device. It is not

Limited Warranty

This Nortek Security & Control product is warranted against defects in material

and workmanship for 12 months. Nortek Security & Control does not warrant

this product to consumers.

There are no obliga ons or liabili es on the part of Nortek Security & Control

for consequen al damages arising out of or in connec on with use or

performance of this product or other indirect damages with respect to loss of

property, revenue, or proﬁ t, or cost of removal, installa on, or reinstalla on.

All implied warran es for func onality, are valid only un l the warranty expires.

This Nortek Security & Control LLC Warranty is in lieu of all other warran es

expressed or implied.

For technical support in the USA and Canada:

800.421.1587

Email: [email protected]

Visit www.nortekcontrol.com for technical support hours of opera on

For technical support outside of the USA and Canada:

Contact your regional distributor

Visit dealer.2gig.com for a list of distributors in your region

Patent Pending.

2GIG® is a registered trademark of Nortek Security & Control LLC.

Recipient to add recipients associated with the no ﬁ ca on.

No ﬁ ca on.

which the receiver is connected

void the user's authority to operate the equipment.

intended to replace any other safety considera ons.

10017336A X2