GREAT PLANES Micro Whizz 사용 설명서 - 페이지 3

{카테고리_이름} GREAT PLANES Micro Whizz에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. GREAT PLANES Micro Whizz 16 페이지.

페이지 인쇄

If you have not flown this type of model before, we

recommend that you get the assistance of an experienced

pilot in your R/C club for your first flights. If you're not a

member of a club, your local hobby shop has information

about clubs in your area whose membership includes

experienced pilots.

In addition to joining an R/C club, we strongly recommend you

join the AMA (Academy of Model Aeronautics). AMA

membership is required to fly at AMA sanctioned clubs. There

are over 2,500 AMA chartered clubs across the country.

Among other benefits, the AMA provides insurance to its

members who fly at sanctioned sites and events. Additionally,

training programs and instructors are available at AMA club

sites to help you get started the right way. Contact the AMA at

the address or toll-free phone number below:

TOOLS & SUPPLIES REQUIRED

Hobby knife (HCAR0105)

#11 blades (HCAR0211)

Needle-nose pliers

Pliers with wire cutters (HCAR0630)

Small Phillips head screwdriver

Medium-sized flat-head screwdriver

Small piece of medium grade sandpaper

Ruler

Electric drill and 1mm drill bit

6-minute Epoxy (GPMR6045)

Denatured alcohol (for epoxy clean up)

1/2 oz. Medium Pro

™

CA debonder

Pro Wood Glue (GPMR6160)

Great Planes 1" x 6" Velcro

Top Flite

Panel Line Pen (TOPQ2510)

Great Planes Silver Solder Kit (GPMR8070)

Hobbico

Soldering Iron (HCAR0776)

1/16" [1.6mm] x 3/4" [19mm] x 4" [102mm] scrap balsa

3/32" [2.4mm] x 1" [25mm] x 4" [102mm] scrap balsa

Hardware & Accessories

This is the list of hardware and accessories required to

finish the Great Planes Micro Whizz ARF. Order numbers

are provided in parentheses.

Academy of Model Aeronautics

5151 East Memorial Drive

Muncie, IN 47302

Tele: (800) 435-9262

Fax (765) 741-0057

Or via the Internet at:

http://www.modelaircraft.org

CA (GPMR6007)

(GPMQ4480)

Motor/Gearbox/Prop

The Micro Whizz ARF was flown extensively with an

ElectriFly

™

S-280 5:1 Ratio STD Gearbox unit

(GPMG0200). The ElectriFly Ferrite BB Motor (GPMG0305)

was used for power along with an APC 9 x 6 SloFly

Propeller (APCQ5013). This set-up also requires a 3mm

Shaft Adapter (GPMQ4600). This is an excellent power

unit for this airplane.

Battery Recommendations

The Micro Whizz operates best using the 8-cell NiMH

from ElectriFly (GPMP0072)

Radio Equipment

The Micro Whizz requires a mini receiver such as the

ElectriFly 4 channel FM Mini Receiver (GPML0045) and

3 Futaba

S-3103 Micro Mini Servos (FUTM0037).

Speed Control

An electronic speed control with BEC (Battery Eliminator

Circuitry) is required. The BEC allows both the motor and

the radio system to be powered by the same battery and

eliminates the additional battery required to power the

radio gear. The ElectriFly C-10 Mini Electronic Speed

Control (GPMM2010) is recommended for the Micro Whizz.

Chargers

The best type of charger to use is a peak charger,

because it charges the batteries until they are fully

charged, then automatically switches to a trickle charge

mode. The Great Planes ElectriFly Peak Charger

(GPMM3000) is suitable for nickel-metal hydride

batteries, NiCds and transmitter battery packs.

You may want to consider the ElectriFly Triton

computerized

charger,

(GPMM3150). This unit will pay great dividends by

extending battery life and is capable of charging virtually

every hobby battery on the market today.

IMPORTANT BUILDING NOTES

•

When you see the term test fit in the instructions, it

means that you should first position the part on the

assembly without using any glue, then slightly modify or

custom fit the part as necessary for the best fit.

•

Whenever the term glue is written you should rely upon

your experience to decide what type of glue to use. When a

specific type of adhesive works best for that step, the

instructions will make a recommendation.

discharger,

and

cycler

™