AFG 2.0AT 사용자 설명서 - 페이지 16
{카테고리_이름} AFG 2.0AT에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. AFG 2.0AT 20 페이지.
페이지 인쇄
MONTH
MONTHLY GOAL
WEEK#
DISTANCE
CALORIE$
TIME
MONTHLY TOTALS:
MONTH
MONTHLY GOAL
WEEK#
DISTANCE
CALORIE$
TIME
MONTHLY TOTALS:
i ¸ ,,,,_
MONTH
MONTHLY GOAL
WEEK#
DISTANCE
CALORIE$
TIME
MONTHLY TOTALS:
COMMON P RODUCT QUESTIONS
ARETHE SOUNDS M YTREADMILL MAKES NORMAL ?
All treadmills make a certain type of thumping noise due to the belt riding over the rollers, especially new
treadmills. This noise will diminish overtime, although may not totally go away. Overtime, the belt will
stretch, causing the belt to ride smoother overthe rollers.
WHY I$ THETREADMILL I PURCHASED LOUDER THAN THEONE AT THE STORE?
All fitness products seem quieter in a large store showroombecause there is generally morebackground noise
than in your home.Also, there wit be less reverberation on a carpeted concretefloor than on a woodoverlay
floor. Sometimesa heavy rubber mat will help reducereverberation through the floor. If a fitness product is
placed close to a wall, there wit be morereflected noise.
WHEN SHOULD I BEWORRIED A BOUT A NOISE?
As long as the soundsyour treadmill makesare no louder than a normal conversational tone of voice,it is
considerednormal noise.
PROBLEM: Theconsoledoes not light up and/or the belt does not move.
SOLUTZON,", V erify the foflowing:
DOESTHEREDLIGHTONTHEON/OFF SWITCH LIGHTUP?
IF YES..
,, Doublecheck that all connectionsare secure,especially the consolecable. Unplug and reconnectthe console
cable to verify.
o Make sure the consolecable is not pinched or damaged in any way.
o Turnthe power off, unplug the power cable and wait 60 seconds. Removemotor cover.Wait until aft red LED
lights havegone off on the motor control board beforeproceeding.Next, verify that noneof the wires connected
to the lower board are looseor disconnected.
iF NO:
0
0
0
Verifythat the outlet the machine is plugged into is functional Doublecheck that the breakerhas not tripped,
it is on a dedicated 20-amp circuit, it is not on a GFCIequipped outlet, and it is not plugged into a power
strip/surge protector or extensioncord.
Thepower cord is not pinched or damagedand is properlyplugged into the outlet AND the machine.
Thepower switch is turned to the ONposition.
PROBLEM: The treadmill circuit breaker trips during a workout.
SOLUTION:
Verify the following:
,, Make sure the treadmill is plugged into a dedicated 20-amp circuit.
,, Verifythat you do not have the machine on an extension cord or surge protector.
,, Confirm that the machine is not plugged into a GFCI-equipped outlet or on a circuit that has a
GFCI-equipped outlet on it.
,, Lubricate treadmill deck if necessary.
PROBLEM: Therunning belt does not stay centered during a workout.
SOLUT!ON: Verify the following:
,, Make sure the treadmill is on a level surface.
,, Verify that the belt is properly tightened and centered (Refer to the Adjustment section for detailed
directions).
i
iii_ i
_ii_ii_i
_!!I i I _I_!I_I
2.0AT
Rev.l.9.indd
30-31
3/3/08
11:12:40AM