2gig Technologies 2GIG-FT6-345 설치 지침 - 페이지 2

{카테고리_이름} 2gig Technologies 2GIG-FT6-345에 대한 설치 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. 2gig Technologies 2GIG-FT6-345 2 페이지. Flood and temperature detector

2gig Technologies 2GIG-FT6-345 설치 지침
2GIG Flood & Temperature Control Instruction Manual
Flood Detector Operation
Metal contacts on the top and bottom of the detector can detect the presence
of water. Be certain to place the detector in a manner that does not impede the
detector's ability to detect water. NOTE: Do not place on a metal or conductive
surface.
METAL CONTACTS
(TOP)
Figure 5. Flood Detector Contacts
Securing the Detector
In areas where the detector could be accidentally moved, secure the detector in
place with the provided double sided adhesive tape.
NOTE: Make sure you secure the tape without covering any of the three metal
contacts.
Figure 6. Detector Double Sided Adhesive Tape Application
DOUBLE SIDED ADHESIVE TAPE
Flood/Temperature Specifications
Operating Temperature:
Operating Rel. Humidity:
Operating Frequency:
Battery Type:
Projected Battery Life:
Supervisory Interval
2 Copyright © 2018 Nortek Security & Control
METAL CONTACTS
(BOTTOM)
32°to 104° F (0° to 40° C)
5 to 95%, non-condensing
345 MHz
CR123A 3V lithium battery
5 Years
70 Minutes
REGULATORY INFORMATION
This equipment has been tested and found to comply with the limits for Class B Digital Device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the
following measures.
Reorient or relocate the receiving antenna
Increase the separation between the equipment and receiver
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected
Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. Ľexploitation est autorisée aux deux conditions suivantes: (1) ľappareil
ne doit pas produire de brouillage, et (2) ľutilisateur de ľappareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible ďen compromettre le fonctionnement.
FCC COMPLIANCE STATEMENT
This device complies with FCC Rules and Regulations as Part 15 devices as well as Industry
Canada license exempt RSS Rules and Regulations. Operation is subject to the following two
(2) conditions: This device may not cause harmful interference. This device must accept any
interference received, including interference that may cause undesired operation.
INDUSTRY CANADA (IC) COMPLIANCE
This device complies with Industry Canada license‐exempt RSS standard(s). Operation is subject
to the following two conditions: (1) this device may not cause interference, and (2) this device
must accept any interference, including interference that may cause undesired operation of the
device. Repairs to certified equipment should be made by an authorized Canadian maintenance
facility designated by the supplier. Any repairs or alterations made by the user to this equipment,
or equipment malfunctions, may give the telecommunications company cause to request
the user to disconnect the equipment. Users should ensure for their own protection that the
electrical ground connections of the power utility, telephone lines and internal metallic water pipe
system, if present, are connected together. This precaution may be particularly important in rural
areas. Users should not attempt to make such connections themselves, but should contact the
appropriate electric inspection authority, or electrician, as appropriate.
LIMITED WARRANTY
This Nortek Security & Control LLC product is warranted against defects in material and
workmanship for two (2) years. This warranty extends only to wholesale customers who buy
direct from Nortek Security & Control LLC or through Nortek Security & Control normal distribution
channels. Nortek Security & Control does not warrant this product to consumers. Consumers
should inquire from their selling dealer as to the nature of the dealer's warranty, if any.
There are no obligations or liabilities on the part of Nortek Security & Control for consequential
damages arising out of or in connection with use or performance of this product or other indirect
damages with respect to loss of property, revenue, or profit, or cost of removal, installation, or
reinstallation. All implied warranties for functionality, are valid only until the warranty expires.
This Nortek Security & Control Warranty is in lieu of all other warranties expressed or implied.
Nortek Security & Control LLC | 2GIG
5919 Sea Otter Place, Suite 100
Carlsbad, CA 92010 USA
For technical support in the USA and Canada:
855-2GIG-TECH (855-244-4832)
Email:
Visit
www.nortekcontrol.com
for technical support hours of operation.
For technical support outside of the USA and Canada:
Contact your regional distributor.
Visit
www.2gig.com/dealers/
for a list of distributors in your region.
10021591 A