Emergi-Lite HP Series 매뉴얼 - 페이지 3

{카테고리_이름} Emergi-Lite HP Series에 대한 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Emergi-Lite HP Series 4 페이지. Battery unit for hazardous locations

페이지 인쇄

Connections for 277Vac line voltage (Figure 6):

a. Install three red clips (provided) one on the red wire (heater),

and white and orange wires (transformer).

b. Self-connect red wire (heater) on its own clip (electrical cap).

c. Connect white wire (heater) to clip of white wire (transformer).

d. Connect red wire (thermostat) to clip of orange wire

(transformer).

Thermostat

Red

White(Netural)

Black(120V)

Orange(277V)

Figure 6

NEXUS (option): refer to page 4 for electrical connections and

commissioning.

8. Install the batteries (if shipped separately) and connect the battery

wires to the charger board. Each battery has its own cable and

must be connected to the charger.

9. Tighten the batteries and cables with the flexible Velcro strap.

10. For vertical pole mount: in addition to the Velcro strap, install the

metal strap and screws provided in the installation kit (Fig 1.) to

hold the battery(ies).

11. Close the cover and tighten the screws.

SCREWS MUST BE TORQUED TO AT

LEAST 12INLB TO ENSURE A WATER-

WARNING:

TIGHT SEAL BETWEEN THE COVER AND

HOUSING.

12. Turn on AC power.

Manual Testing

The equipment comes standard with a one-

button infrared remote control.

Before starting manual testing remove plastic

tab from battery compartment on remote

control.

To initiate a test: orient the remote control

towards the pilot light of the unit and press the

TEST button.

13. Test function (power on, stand-by): press the TEST button, the unit

will start a one-minute test. Pressing the button again will abort the

test in progress.

14. Load disconnect: this option can be used during a power failure to

save battery power during daylight hours. Press the TEST button,

the emergency lights will turn off. By pressing the test button again

the emergency lights will turn back on.

15. On-charger manual test: the unit also has a test button installed on

the charger module located on the bottom of the unit (See figure 7).

This is useful during maintenance, with the unit door open. The

button performs the same functions as the remote control.

Automatic self-test and diagnostic (Option)

16. Self-test: Once power is supplied to the unit it will automatically

initiate a routine self-test calendar as follows:

a. Verifies battery connection, battery failure, charger board failure

and lamps failure.

Emergi-Lite®

Tel: (888) 552-6467

White

Red

Heater Pad

Yellow

Fax: (800) 316-4515

HP Series Battery Unit for hazardous locations

b. Executes one-minute monthly self-test

c. Executes a 30 -minute self-test every 6th month

d. Executes a 90 -minute self-test every 12th month

17. Diagnostic: The unit is equipped with a bi-color LED pilot light and

indicates the following status:

a. Green color: AC-on / self-test

b. Red color: Service alarm

A diagnostic label is placed on the unit cover.

Green

Red

Steady On

Red

One Blink

Red

Two Blinks

OOO

Red

Three Blinks

OOOO

Red

Four Blinks

Transfer time delay (Option)

This feature works when the AC power is restored: it keeps the

emergency lights "on" for a period of: 5, 10 or 15 minutes (factory set).

If the battery depletes before the end of the time delay, the lamps turn

off and the unit goes in stand-by mode.

The Time Delay feature can be enabled or disabled in the field with the

following procedure (See figure 7):

a. Make sure that the battery and the AC main power are both

disconnected.

b. Disconnect the jumper JP4 to activate the Time Delay

c. Continue with the standard installation

enabled

No TD

JP4

Buzzer Silent

"ON"

JP7

Test switch

Figure 7 Charger module

Audible service alarm (Option)

This function acts in case of a Service alarm by generating a beep

every two seconds.

During a service alarm the beep can be silenced by pressing the

remote control test switch.

The audible service alarm can also be permanently disabled in the field

by disconnecting the jumper JP7 (See figure 7).

www.emergi-lite.com

Steady

AC On

Blinking

Testing Mode

Battery disconnect or

Lamp disconnect

Battery Failure

Charger Failure

Lamp Failure

Heater Failure

Low‐voltage

transformer

secondary

Load Fuse

Battery

On‐charger test switch

11/17 750.0020 Rev. A

3/4