ADEMCO VISTA-20P Series 빠른 설치 매뉴얼 - 페이지 2

{카테고리_이름} ADEMCO VISTA-20P Series에 대한 빠른 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. ADEMCO VISTA-20P Series 2 페이지.
ADEMCO VISTA-20P Series에 대해서도 마찬가지입니다: 프로그래밍 매뉴얼 (17 페이지)

페이지 인쇄

AC POWER AND BATTERY CONNECTION

AC POWER CONNECTION

TRANSFORMER

CONNECT THE TRANSFORMER TO TERMINALS 1 AND 2.

SEE WIRE RUN CHART.

TRANSFORMER WIRE RUNS

USE CAUTION WHEN WIRING

Distance from control Wire Size

THE TRANSFORMER TO THE

CONTROL TO GUARD AGAINST

Up to 50 feet

# 20

BLOWING THE TRANSFORMER

50 - 100 feet

# 18

FUSE (THE FUSE IS

100 - 200 feet

# 16

NON-REPLACEABLE).

AFTER ALL WIRING CONNECTIONS ARE COMPLETE, PLUG

TRANSFORMER INTO A 110VAC UNSWITCHED OUTLET (24HR)

USE 1361X10 TRANSFORMER INTERFACE WHEN POWER

LINE CARRIER DEVICES ARE BEING USED.

"AC LOSS" DISPLAYED IF VOLTAGE FALLS BELOW 16.5VAC.

BATTERY

PLACE THE 12-VOLT BACKUP BATTERY IN THE CABINET.

AFTER ALL CONNECTIONS TO THE CONTROL ARE MADE AND

AC POWER HAS BEEN APPLIED, CONNECT THE RED AND

BLACK FLYING LEADS TO THE BATTERY.

CONNECT ONLY AFTER AC POWER HAS BEEN APPLIED.

IMPORTANT: THE PANEL WILL NOT POWER UP INITIALLY ON

BATTERY POWER ONLY. YOU MUST PLUG THE TRANSFORMER

IN FIRST, AND THEN CONNECT THE BATTERY.

SOUNDER CONNECTION

CONNECT SOUNDER TO BELL TERMINALS 3 (+) AND 4 (-).

SOUNDER ACTIVATES UPON ALARM EVENT.

ALARM OUTPUT: 10.5–13.8VDC, 2A MAX. (600mA MAX. FOR

UL USAGE, INCLUDING AUX POWER) STEADY FOR

BURGLARY/PANIC, TEMPORAL PULSE SOUNDING FOR FIRE.

UL: MUST BE A UL LISTED AUDIBLE SIGNAL APPLIANCE RATED

FOR 10.2-13.8 VDC AND BE MOUNTED INDOORS.

CAN USE ADEMCO No. 702 SIREN, OR 12V BELL.

A BATTERY MUST BE INSTALLED BECAUSE THE BATTERY

SUPPLIES THE CURRENT.

FOR SOUNDER SUPERVISION

UL: BELL SUPERVISION IS REQUIRED

FOR FIRE ALARM INSTALLTIONS.

EXTERNAL ALARM SOUNDER

IF BELL SUPERVISION IS

ENABLED (RED JUMPER ON

CONTROL BOARD IS CUT

TERM 4

AND

91 ENABLED)

2000 OHM

CONNECT A 2000 OHM

OBSERVE

EOL

POLARITY

RESISTOR ACROSS THE

TERM 3

RESISTOR

EXTERNAL SOUNDER AS

SHOWN BY THE DOTTED LINE.

DO NOT CONNECT THE RESISTOR AT THE ALARM OUTPUT TERMINALS THEMSELVES!

RF RECEIVERS & TRANSMITTERS

MODULE

SET RECEIVER DEVICE ADDRESS TO "00" (SET SWITCHES TO

THE RIGHT, "OFF" POSITION).

MOUNT THE RECEIVER INSIDE THE CABINET OR REMOTELY

WITHIN A NOMINAL RANGE OF 200 FEET FROM TRANSMITTERS,

IN HIGH, CENTRALLY LOCATED AREA.

CONNECT THE RECEIVER'S WIRE HARNESS TO THE CONTROL'S

ECP TERMINALS. SEE RECEIVER'S INSTRUCTIONS FOR

ANTENNA MOUNTING, ETC.

INSTALL TRANSMITTERS ACCORDING TO THEIR INSTRUCTIONS.

WIRELESS ZONE NUMBERS

VISTA-20P:

VISTA-15P:

40 TRANSMITTER ZONES: 9-48

26 TRANSMITTER ZONES: 9-34

16 BUTTON ZONES: 49-64

8 BUTTON ZONES: 49-56

ULC NOTE: THE RF SUPERVISION PERIOD FOR THE V20PCN AND

V15PCN IS THREE HOURS FOR FIRE ZONES (ZT 9 AND 16) AND

12 HOURS FOR ALL OTHER ZONE TYPES.

BATTERY FUSE

FOR REPLACEMENT,

RECHARGABLE

USE SAME VALUE

CANADA: USE PSC04.

BATTERY

(e.g. ADEMCO No. 90-12)

SEE INSTALLATION INSTRUCTIONS.

(12V, 4AH)

FUSE NOTE

SEALED LEAD

MAY HAVE PTC IN

ACID TYPE

PLACE OF FUSE.

RED

BLACK

UL: PLC DEVICES AND 1361X10

ARE NOT UL LISTED FOR FIRE

OR BURGLARY FUNCTIONS

AND ARE INTENDED FOR

HOME AUTOMATION.

1321

TERMINALS

(1321CN IN CANADA)

1 & 2

16.5VAC, 25VA, CLASS 2

PLUG-IN TRANSFORMER

ECP AUX POWER OUTPUT

10.5-13.8VDC 600mA MAX.

(500mA MAX. FOR UL INSTALLATIONS)

AC BELL

GND

4219/4229

EXPANDER

RECEIVER

MODULE

SENSORS

(USE 1K EOLR)

COMMUNICATION

DEVICE

CONTROLLED

DEVICES

4204

RELAY

BLACK

RED

GREEN

YELLOW

KEYPAD

KEYPADS AND ADDRESSABLE DEVICE CONNECTION

CONNECT KEYPADS AND OTHER ADDRESSABLE DEVICES TO ECP TERMINALS 4-7.

(SEE "SETTING KEYPAD ADDRESS BOX TO SET KEYPAD ADDRESSES.)

TOUCHSCREEN NOTE: TOUCHSCREEN KEYPADS MAY REQUIRE AN EXTERNAL

POWER SUPPLY DUE TO AUX POWER LIMITATIONS.

SET EACH MODULE'S ADDRESS ACCORDINGLY:

DEVICE

ADDRESS

DEVICE

ADDRESS

KEYPADS

16 - 23

5800TM

28 (PART. 1 ONLY)

4219, 4229

07 - 11

COMM DEVICE

4204

12 - 15

4286

RF RECEIVER

TOUCH SCREENS

V15P: 1, 2

V20P: 1, 2, 5, 6

TRIGGER CONNECTOR

USED FOR 1361X10

TRANSFORMER

CONNECTIONS AND FOR

ON-BOARD TRIGGERS.

AUX PWR

PROGRAM RELAY

OUT 17 = 100mA MAX

OUTPUT

AS ZONE TYPE 54

OUT 18 = 20mA MAX

TERMINALS

(FIRE ZONE RESET)

1 2 3 4

5 6

7 8

OPTIONAL

CONTACT OPENS MOMENTARILY

1361X10

UPON FIRE ALARM RESET

TO OUTPUT 17

PROGRAM OUTPUT 17 FOR

"OUT NORM LOW" = YES IN

79 MENU MODE AND AS ZONE

BLUE (DATA)

TYPE 54 IN

80 MENU MODE

MAX. CURRENT = 100 mA

PURPLE (COM)

BLACK (SYNC)

(USE SA4120XM-1 CABLE)

(+)

TO ZONE 2 8 TERM.

RED JUMPER

CUT FOR BELL SUPERVISION.

( )

ALSO, CONNECT 2000 OHM

RESISTOR DIRECTLY ACROSS

SOUNDER AND ENABLE FIELD

91.

ECP DEVICES

HARDWIRE ZONES

AUX

OUT

Z1+

GND

GND Z6

2000

OHMS

EOLR

2-WIRE SMOKE

DETECTORS

(16 MAX) OR

STANDARD

2K EOLR

HARDWIRE ZONE CONNECTION

OPEN CIRCUIT DEVICES CONNECT IN PARALLEL ACROSS

THE LOOP; FOR EOLR ZONES, CONNECT THE EOLR

ACROSS THE LOOP WIRES AT THE LAST DEVICE.

CLOSED CIRCUIT DEVICES CONNECT IN SERIES IN THE

HIGH (+) SIDE OF THE LOOP; FOR EOLR ZONES, CONNECT

THE EOLR IN SERIES FOLLOWING THE LAST DEVICE.

EOLR NOTE:

IF THE EOLR IS NOT AT THE END OF THE LOOP, THE

ZONE IS NOT PROPERLY SUPERVISED AND THE SYSTEM

MAY NOT RESPOND TO AN "OPEN" ON THE ZONE.

UL NOTE:

FOR UL COMMERCIAL BURGLARY ALARM INSTALLATIONS,

USE EOLR ZONES.

DOUBLE-BALANCED ZONE

ZONE DOUBLING

VISAT-20P ONLY

VISTA-20P ONLY

PROVIDES ZONE TAMPER

PROVIDES TWO HARDWIRED

PROTECTION AND SHOULD BE

N.C. ZONES FOR EACH

USED AS BURGLARY ZONES ONLY.

STANDARD HW ZONE

A SHORT ACROSS THE EOL

(BUT DOES NOT INCREASE

CAUSES A TAMPER CONDITION.

TOTAL NUMBER OF ZONES

SUPPORTED. A SHORT ACROSS

THE EOL ON EITHER ZONE

CAUSES A TAMPER CONDITION.

ZONE NUMBERS USED FOR

DOUBLING CANNOT BE USED

FOR ANYTHING ELSE.

ZONE 2

ZONE 10

ZONE 3

ZONE 4

DO NOT USE DOUBLE-BALANCED ZONES

OR ZONE DOUBLING FOR FIRE ZONES.

4-WIRE SMOKE DETECTOR CONNECTIONS

RELAY

BLK

RED

EOL

POWER

N.O.

SUPERVISION

N.C.

RELAY MODULE

A77-716B.

USE N.O.

CONTACT,

VIOLET

WHICH CLOSES

WHEN POWER

IS APPLIED.

4-WIRE SMOKE

2000

OR COMBUSTION

DETECTOR

OHMS

EOLR

HEAT

DETECTOR

HANDSET

INCOMING

GND

TIP

RING

TIP

RING

GND

EARTH

GROUND

EARTH GROUND CONNECTION

2000

THIS CONTROL DOES NOT NORMALLY NEED AN EARTH GROUND. IF

OHMS

DESIRED FOR ADDITIONAL PROTECTION, CONNECT TERMINAL 25 TO A

EOLR

GOOD EARTH GROUND. EXAMPLES OF GOOD EARTH GROUNDS:

VISTA-20P ONLY

METAL COLD WATER PIPE: USE A NON-CORROSIVE METAL STRAP

(COPPER IS RECOMMENDED) FIRMLY SECURED TO THE PIPE TO WHICH

THE GROUND LEAD IS ELECTRICALLY CONNECTED AND SECURED.

AC POWER OUTLET GROUND: AVAILABLE FROM 3-PRONG, 120VAC

POWER OUTLETS ONLY. TO TEST THE INTEGRITY OF THE GROUND

TERMINAL, USE A 3-WIRE CIRCUIT TESTER WITH NEON LAMP

INDICATORS, SUCH AS THE UL LISTED IDEAL MODEL 61-035, OR

EQUIVALENT, AVAILABLE AT MOST ELECTRICAL SUPPLY STORES.

RING (GRAY)

PREMISES

TIP (BROWN)

PHONES

RING (RED)

RJ31X

TIP GREEN)

PHONE CONNECTION

CONNECT PHONE LINE DIRECT

CONNECT CABLE WIRES TO

TERMINALS 21-24 AS SHOWN.

WIRE COLORS REPRESENT THE

COLORS OF THE CABLE TO THE

RJ31X JACK.

CONNECT INCOMING PHONE

LINE AND HANDSET WIRING TO

ZONE

THE MAIN TERMINAL BLOCK

PAIRS

(VIA AN RJ31X JACK; CA38A IN

CANADA) AS SHOWN.

2 / 10

3 / 11

4 / 12

5 / 13

6 / 14

7 / 15

8 / 16

6.2k

KEYSWITCH WIRING CONNECTIONS

1 2 3 4

5 6

7 8

TRIGGER CONNECTOR

UL: SEE INSTALLATION INSTRUCTIONS

FOR USAGE AND LIMITATIONS.

4146 KEYSWITCH

STANDARD

(ARMED)

KEYPAD

RED

CABLE

YELLOW

(READY)

GREEN

WHITE

820

ohms

BLACK

RED

TAMPER

SWITCH (N. C.)

BROWN

TYPICAL ZONE

LOCK

ON CONTROL

SWITCH (N. O.)

BOARD

BLUE

2K OHM EOLR

INCOMING

TELCO

SETTING KEYPAD ADDRESS

HOLD

DOWN

THREE

SECONDS

ARMED

OFF

AWAY

STAY

READY

MAX

TEST

BYPASS

INSTANT

CODE

CHIME

READY

POWER UP THE KEYPAD. WITHIN 60 SECONDS OF

POWER-UP, PRESS AND HOLD DOWN THE [1] & [3] KEYS

AT THE SAME TIME FOR 3 SECONDS.

ENTER THE PROPER "TENS" DIGIT OF THE KEYPAD'S

ADDRESS, THEN ENTER THE PROPER "ONES" DIGIT

OF THE KEYPAD'S ADDRESS.

NOTE: FIRST KEYPAD IS ADDRESS 16

PRESS [ ] TO SAVE THE DISPLAYED ADDRESS AND

EXIT ADDRESS MODE.

V15P_V20P_quick-guide_CL