Emeril Lagasse PPC772 소유자 매뉴얼 - 페이지 13

{카테고리_이름} Emeril Lagasse PPC772에 대한 소유자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Emeril Lagasse PPC772 17 페이지.

페이지 인쇄

Troubleshooting

Symptom

Possible Cause

Cannot open Pressure

Lid

Inner Lid is upside down

Pressure Lid does not

Inner Lid Rubber Gasket is not properly

lock

installed

Food level is too high to allow the lid to

close.

Cannot open Pressure

Float Valve and Pressure Release Valve

Lid after pressure is

are still raised

released

Pressure Lid incorrectly installed

Inner Lid not installed

Air escapes from the

rim of the Pressure Lid

Inner Lid Rubber Gasket not installed or

and pressure will not

incorrectly installed

increase

Food residue on Inner Lid Rubber Gasket

Inner Lid Rubber Gasket is damaged

or worn out

Food stuck on Float Valve Rubber Gasket

Air escapes from Float

Valve during operation

Float Valve Rubber Gasket not installed

or installed incorrectly

Float Valve Rubber Gasket is worn out

Appliance is not filled with enough food

or water

Float Valve does

not rise

Air is escaping from rim of Lid and/or

from Pressure Release Valve

Float Valve not assembled correctly

Emeril Lagasse Pressure Cooker Plus™ | Models: PPC771, PPC772 & PP772P

Solution

DO NOT FORCE OPEN.

Install the Inner Lid with the tab facing downward (ee INNER LID

ASSEMBLY in INSTRUCTIONS FOR PRESSURE LID ASSEMBLY, p. 14).

Press the middle hole in the Inner Lid onto the Pressure Lid's center

knob.

Remove some food so that it is not touching the Inner Lid.

Ensure the Pressure Release Valve is open. CAUTION: Hot steam may be

released during this process. DO NOT FORCE THE UNIT OPEN. Do not

place your face, hands, or body near the valve opening. Do not wrap your

arms or body around the Unit to try to open it. Allow the Unit to cool for

30 mins. before attempting to open again.

See ATTACHING LID in INSTRUCTIONS FOR PRESSURE COOKING,

p. 18.

Install Inner Lid (see INNER LID ASSEMBLY in INSTRUCTIONS FOR

PRESSURE LID ASSEMBLY, p. 14).

Install Inner Lid Rubber Gasket.

Clean Inner Lid Rubber Gasket.

Replace Inner Lid Rubber Gasket. Contact Customer Service (see the

back of the manual for contact information). for replacement parts.

Clean Float Valve Rubber Gasket

Install Inner Lid (see FLOAT VALVE AND RED PRESSURE INDICATOR

ASSEMBLY in INSTRUCTIONS FOR PRESSURE LID ASSEMBLY, p. 15).

Replace Float Valve Rubber Gasket. Contact Customer Service

for assistance (see the back of the manual for contact information).

Check recipe for proper quantities of solids and liquids.

Contact Customer Service for assistance (see the back of the manual

for contact information).

Float Valve should be able to move up and down, stopping only when

its Rubber Gasket meets the Lid interior. Ensure that its Rubber Gasket

is clean and the Float Valve can move freely.*

CONTINUED ON NEXT PAGE

Troubleshooting

Symptom

Possible Cause

Liquid spitting out of

Too much liquid in Unit

Float Valve

Unit turns off

Appliance is overheated

unexpectedly

Display reads "LID" and

Lid not positioned correctly or not fully

beeping sound occurs

closed

Lid does not open

Lid is put on incorrectly

*NOTE: If necessary to reassemble Float Valve, see FLOAT VALVE AND RED PRESSURE INDICATOR ASSEMBLY, p. 15.

DISPLAY ERROR INDICATOR

Error Code

Cause of Error

Bottom sensor open

Bottom sensor short circuit

Unit has overheated

Pressure switch malfunction

LID

Wrong lid

NOTE: DO NOT use or attempt to repair a malfunctioning appliance.

*See the back of the manual for Customer Service contact information.

Unit Specifications

Model

Supply

Rated

Number

Power

PPC771

AC 120V ~60Hz

1000W

PPC772

AC 120V ~60Hz

1300W

PPC772P

AC 120V ~60Hz

1300W

Solution

Allow the cooking cycle to finish. Clean the Float Valve thoroughly. Use

less liquid in future recipes.

Unplug and let the Unit cool for 30 minutes in order to reset.

Adjust Lid by following ATTACHING LID in INSTRUCTIONS FOR

PRESSURE COOKING, p. 18.

NOTE: Non-pressure programs require a glass lid or an unlocked lid.

DO NOT FORCE LID OPEN. Unplug the Unit and allow to cool down for at

least 30 minutes. Then, attempt to remove the Lid.

Solution

Contact Customer Service*

Let the Unit cool down before use

Contact Customer Service*

Attach the correct lid before use

Capacity

Working

Safety Working

of Inner Pot

Pressure

6 qt.

0–80 kPa

80–90 kPa

8 qt.

0–80 kPa

80–90 kPa

8 qt.

0–80 kPa

80–90 kPa

Emeril Lagasse Pressure Cooker Plus™ | Models:PPC771, PPC772 & PP772P