Automatic Systems TR450 설치 매뉴얼 - 페이지 11
{카테고리_이름} Automatic Systems TR450에 대한 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Automatic Systems TR450 13 페이지. Tripod turnstile
페이지 인쇄3.5.
Electrical connections and initial power-up
•
The electrical connections must be made according to the diagram affixed inside the housing
(diagram Automatic Systems 2TR4A5B5).
6:2
6:3
6:5
6:1
Legend:
6:1 Board AS841/2
6:2 F24 (24V 3.15A fuse)
6:3 F230 (230V 1.6A fuse)
6:4 EREA 230V/24V 100VA transformer
6:5 Transformer connection block
6:6 SW1 (16A 250VAC main switch)
6:7 Power supply & controls connection block
Make sure that the power supply cables are not live. All internal connections are factory-
made.
If necessary, cut off the excess cable length. Connect the 230V single-phase power supply
wires to the terminals R and N on the connection block (6:7), and the earth wire to the
terminal TR. Make sure the equipment is correctly earth bonded (housing and associated
metalwork).
Proceed with all other electrical connections depending on the equipment specifications
(control wiring, etc.).
Route all cables via the cable entry holes and secure in the cable fastenings provided,
ensuring that they are held clear of the turnstile mechanism's moving parts.
Check the state of the 230V 1.6A (6:3) and 24V 3.15A (6:2) fuses on the control logic.
After the power supply from the remote isolator has been energised, test for correct polarity,
supply voltage and earthing, power up the equipment by putting the main switch (6:6) to the
ON position.
Automatic Systems TR450-GB
F220
F24
220V
B1
24V
RCPTF 11
-
3d
10
AC
24V
80Ohm
5
10A 220VAC
B
4
+
3
B
FC
RL1
CP
SBK C3200/2200
AJ
EL
O
C
F
O
C
F
22 21 20 19 18 17 16 15 14 13 12
6:13
6:12
6:11
Note: The relay RL1 or RL2 is mounted only for a mechanism type 4 or type 5.
If the relay is not mounted, protect the connector with adhesive tape.
YD-XX
MQ-1302
31/08/97
Automatic Systems
6:4
6:6
SW1
AS841/2
ON
OFF
SW2PL
B2
RCPTF 11
-
3d
10
AC
24V
80Ohm
5
10A 220VAC
A
4
+
3
A
FC
RL2
CP
SBK C3200/2200
AJ
EL
O
C
F
O
C
F
11 10 9
8
7
6
5
4
3
2
1
6:9
6:8
6:10
Electrical control logic (model shown: type A3/B5)
6:8 Internal connection block direction A
6:9 Operation mode selector direction A (3-4-5)
6:10 RL1 (5A relay direction A)
6:11 Internal connection block direction B
6:12 Operation mode selector direction B (3-4-5)
6:13 RL2 (5A relay direction B)
Fig. 6
Installation TR450
SER. N°
TR
6
R
N
3
4
6:7
5
51
6
p. 11/12
2-1105GB
Rev.: A