AirCycler FR-V 지침 - 페이지 2
{카테고리_이름} AirCycler FR-V에 대한 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. AirCycler FR-V 2 페이지.
페이지 인쇄INSTALLATION
Step 1—Controller Location
The AirCycler® can be installed anywhere in your home. It
can be installed near a thermostat or out of view on/near
the air handler unit. The wiring configuration is flexible.
Warning: Before installing the AirCycler®, turn off all
power to the furnace. There may be more than one power
to disconnect. Electrical shock can cause injury or death.
Step 2 – Installing the AirCycler®
1.
Remove the AirCycler® cover from wall plate
(mounting base) to expose mounting holes.
(Figure 2)
2.
Route wires through large hole in the mounting base.
Mount base against wall and mark wall through 3
mounting holes.
3.
Drill 3 - 3/16-in. pilot holes in wall where marked.
4.
Secure mounting base to wall with 3 screws
(provided), making sure all wires extend through hole
in mounting base.
5.
Adjust length and routing of each wire to reach
proper terminal and connector block on mounting
base with 1/4 in. of extra wire. Strip only 1/4 in. of
insulation from each wire to prevent adjacent wires
from shorting together when connected.
6.
Connect wires to proper terminals of the connector
block. (Figure 3) Both (R) and (C) must be connected
for proper operation.
Figure 2
7.
Improper wiring or installation may damage the
controller. Check to make sure wiring is correct
before proceeding with installation or turning the
unit on.
8.
Push any excess wire into wall and against mounting
base.
9.
Snap cover onto base making sure pins align with
sockets in connector.
10. Once powered the AirCycler® will automatically
enter into operating mode.
4.50 in.
11.5 cm
Figure 3
CONFIGURATION
The three keys on the exterior of the AirCycler are used to
configure the AirCycler®. (Figure 4)
There are two settings that are adjustable with the
AirCycler® FR and four settings with the AirCycler® FR-V.
Factory default settings
FR settings:
FR-V settings:
FAN OFF 20 minutes
FAN OFF 20 minutes
FAN ON 10 minutes
FAN ON 10 minutes
VENT ON 10 minutes
VENT OFF 20 minutes
Configure FAN ON time
1.
Press the Mode Key once to enter the Menu Mode.
FAN ON will flash on the display.
2.
Use the Increase or Decrease Keys to change the
FAN ON time from 1 - 199 minutes or to select
unlimited ON time (UN). UN allows the fan to operate
continuously.
Configure FAN OFF time
1.
Press the Mode Key again to set the FAN OFF time.
FAN OFF will flash on the display.
2.
Use the Increase or Decrease Keys to change the
FAN OFF time or to select unlimited OFF time (UN).
This will turn the AirCycler® off. This will also keep
the AirCycler® off even after power is lost.
*The AirCycler® retains settings even after power is lost.
NOTE: In humid climates, the FAN OFF time should be
at least 6 minutes. This allows moisture on the AC coil to
dry, preventing condensation in cold supply ducts.
3.50 in.
9 cm
Figure 4
1.30 in.
3.4 cm
Configure VENT ON time – Model FR-V only
1.
Press the Mode Key. VENT ON will flash.
2.
Use the Increase or Decrease Keys to change the
VENT ON time.
Configure VENT OFF time – Model FR-V only
1.
Press the Mode Key. VENT OFF will flash.
2.
Use the Increase or Decrease Keys to change the
VENT OFF time.
SAVE SETTINGS
After configuring the AirCycler® press the Mode Key
again to save settings and to enter into Operating Mode.
OPERATING MODE
If the thermostat activates heating, cooling, or
constant fan operation, the numeric display will read
ON. Otherwise, the display will read FAN OFF and will
display the time remaining until the fan is activated
again. Once activated the display will read FAN ON and
the time remaining for FAN ON time.
The model FR-V has additional settings for outside air
damper cycling. When the fan turns on, the damper
will open and the display will read VENT ON and
indicate the time remaining until the damper closes.
Once the VENT ON time has expired, the damper will
close, the display will read VENT OFF and indicate the
time remaining until the damper opens again.This
4.50 in.
11.5 cm
cycle continues for as long as the fan is running. The
vent will be closed any time the fan is not running
Increase Key
and VENT ON and VENT OFF times will be reset to
programmed values.
Mode Key
POWERING OFF
ON/OFF
Warning: It is not recommended to turn the AirCycler®
off if the unit is used as a ventilation controller. The
AirCycler® can be turned off during extended vacation
Decrease Key
periods or when the windows are open. It is very
important to turn the AirCycler® back on.
1.
In normal Operating Mode. Press and hold the
Mode Key for six seconds to turn the AirCycler® off.
All thermostat functions will continue to operate
normally.
2.
To turn the AirCycler® back on, press the Mode Key.
TESTING
The Test Mode will display fan activity in seconds rather
than minutes. To activate Test Mode, follow these steps.
1.
Press the Mode Key once and then press it again
and hold it for six seconds. The display will indicate
TEST.
2.
Exit Test Mode and return to Operating Mode by
turning the AirCycler® off.
3.
Hold the Mode Key for six seconds, and then press
Mode again to turn the AirCycler® on.
NOTE: As a safeguard, the AirCycler® will automatically
exit Test mode after ten minutes.
3.50 in.
9 cm
1.30 in.
3.4 cm