HID R30E 설치 매뉴얼 - 페이지 2
{카테고리_이름} HID R30E에 대한 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. HID R30E 9 페이지. Iclass se/multiclass se
![HID R30E 설치 매뉴얼](/uploads/products/server2/1899682/1899682.jpg)
INSTALLATION GUIDE
Installation
1
Mounting
2
Wiring
Pigtail
Terminal
Description
Yellow
P1-1
Beeper Input
Orange
P1-2
LED Input (GRN)
Black
P1-3
Ground (RTN)
Red
P1-4
+VDC
Drain
P1-5
Unused
Brown
P1-6
LED Input (RED)
Blue
P1-7
Hold Input
*
Tamper Output. When activated, output syncs to ground (default).
**
Dependent upon reader configuration.
See HTOG Wiegand and Clock-and-Data configurations for more information.
Optional Features
Open Collector Output - Controls an external device (16 VDC Max) operating in Host Mode only. Sink - 40mA / Source - 1mA. See the
iCLASS Application Note for details.
Optical Tamper - A configuration card is necessary to activate the Optical Tamper. Once activated, and when the mounting plate is removed, the Optical
Tamper is activated. Contact HID Technical Support for Optical Tamper options.
Configuration Cards - With the use of configuration cards, the reader can be modified to meet the specific requirements of an installation. Configuration
options include; audio visual, CSN outputs and keypad outputs (keypad models only). Contact HID Technical Support for all reader configuration options.
Hold Input - when asserted, this line either buffers a card or disables a card read until released, as configured.
This Installation Guide is for informational purposes only. HID makes no warranties, expressed or implied, in this summary. Company, product names and data used in sample output
are fictitious. Specifications are subject to change without notice.
© 2014 - 2015 HID Global Corporation/ASSA ABLOY AB. All rights reserved. HID, the HID logo, and iCLASS SE are trademarks or registered trademarks of HID Global in the U.S.
and/or other countries. All other trademarks, service marks, and product or service names are trademarks or registered trademarks of their respective owners.
h id g l o b a l.co m
R10E, RP10E, R15E, RP15E, R30E, RP30E, R40E, RP40E, RK40E, RPK40E, R10MA, RP10MA, RP15MA, R40MA, RP40MA, RPK40MA
BEEP
GPI01
GRN
GPI02
GND
OC/TMPR
+VDC
DATA1/CLK
DRAIN
DATA0/DATA
RED
GPI03
HOLD
GPI04
P1
18 in
P2
(0.46 m)
Pigtail
Red / Green
Tan
Violet
White
Green
Pink
Gray
Page 2
An ASSA ABLOY Group brand
iCLASS SE/multiCLASS SE
Junction box not included
Gasket optional
Observe precautions for handling
ELECTROSTATIC SENSITIVE DEVICES
Note: Previous iCLASS readers had reversed
RS-485 wiring ( P2-7 & P2-6 - A & B).
When upgrading to an iCLASS SE reader,
ensure proper connections as defined
below.
Terminal
Description
P2-7
GPIO1 (RS485-FDX/HDX-A)
P2-6
GPIO2 (RS485-FDX/HDX-B)
P2-5
* Open Collector Output / Tamper
P2-4
**Wiegand Data 1 / Clock
P2-3
**Wiegand Data 0 / Data
P2-2
GPIO3 (RS485-FDX-Z)
P2-1
GPIO4 (RS485-FDX-Y)
PLT-01579 A.3
ATTENTION