Celestron 21043 사용 설명서 - 페이지 4

{카테고리_이름} Celestron 21043에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Celestron 21043 9 페이지. Powerseeker series
Celestron 21043에 대해서도 마찬가지입니다: 사양 (4 페이지), 브로셔 및 사양 (4 페이지), 사양 (2 페이지)

페이지 인쇄
Celestron 21043 사용 설명서
T
T
The PowerSeeker is a refracting telescope that comes on an equatorial mount. This section instructs you on the
proper assembly and use of your PowerSeeker telescope, which is shipped in one box, containing all the parts you
need to assemble it. Unpack and lay out all of the parts in a large, clear area where you'll have room to work.
Keeping track of the parts, use the list below and the telescope diagram to confirm you have, and can identify each
part.
PowerSeeker 60 EQ
1.
Lens Cap
2.
Optical Tube
3.
5x24 Finderscope
4.
Finderscope Bracket
5.
Focuser
6.
Eyepiece
7.
Star Diagonal
8.
Declination Locking Screw
9.
Declination Slow Motion Control
10. Latitude Adjustment Screw
11. Tripod Mounting Head
To set up the tripod, locate the equatorial mount (20), the tripod legs (13), and the tripod mounting head (11).
1.
Slide the two top portions of each tripod leg around the sides of each flange on the tripod mounting head (11).
Make sure that the tripod center support brace hinges (15) are located on the inside of the each leg.
2.
Slide the provided screws through the tripod leg and flange,
until the screw extends out the other side (see Figure 1-2).
Slide the washer and the nut over the screw and tighten. This
can be left slightly loose, to allow for positioning the legs
later, when attaching the accessory tray.
You are now ready to attach the tripod accessory tray.
3.
The tripod tray fits over the holes in the tripod's center
support brace (15). Insert the winged bolts through the holes
in each of the tripod center support braces and thread them
into the holes in the accessory tray. Tighten all bolts to ensure
proper stability to the mount.
A
t
t
a
c
h
i
n
g
t
h
A
t
t
a
c
h
i
n
g
t
h
1.
Place the base of the equatorial mount (20) into the hole on the top of the tripod mounting head (11).
2.
Rotate the equatorial mount until the declination axis (where the counterweight bar (18) goes) is positioned over
one of the tripod legs.
3.
Attach the mount to the tripod by threading the equatorial head mounting screw (12) into the bottom of the
mount
Before attaching the optical tube, the counterweight and slow motion controls should be added to the mount:
1.
Thread the counterweight bar (18) clockwise into the declination axis of the equatorial mount. Slide the
counterweight (17) over the counterweight bar and lock down the screw on the side of the counterweight.
H
E
P
O
W
E
R
S
E
E
K
H
E
P
O
W
E
R
S
E
E
A
s
s
e
m
b
l
i
n
g
A
s
s
e
m
b
l
i
n
g
e
E
q
u
a
t
o
r
i
a
l
M
o
u
n
e
E
q
u
a
t
o
r
i
a
l
M
o
u
n
E
R
6
0
E
Q
R
e
f
r
a
K
E
R
6
0
E
Q
R
e
f
r
a
12.
Equatorial Head Mounting Screw
13.
Tripod Leg
14.
Accessory Tray
15.
Center Support Brace
16.
Tripod Tightening Screws
17.
Counterweight
18.
Counterweight Bar
19.
R.A. Slow Motion Control
20.
Equatorial Mount
21.
Mounting Platform
22.
Objective Lens
Y
o
u
r
T
e
l
e
s
c
o
p
e
Y
o
u
r
T
e
l
e
s
c
o
p
e
Tripod
Mounting Head
t
t
4
c
t
o
r
c
t
o
r
(11)
Figure 1-2