Dynamco Cyclops 661 사용자 지침

{카테고리_이름} Dynamco Cyclops 661에 대한 사용자 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. Dynamco Cyclops 661 2 페이지. Remote car alarm

페이지 인쇄

661 REMOTE CAR ALARM

U S E R I N S T R U C T I O N S

Proudly designed and engineered

in Australia by Dynamco Pty Ltd.

Congratulations on having one of the worlds most advanced

and unique Australian designed and engineered vehicle

security systems, installed in your vehicle!

IMPORTANT NOTICE:

Ensure your installer has programmed your individual PIN code before

taking your vehicle. (see "programming new PIN" section).

BUTTON #1

Arm/Disarm/Siren Stop Panic

a. Arming: During the arm procedure

the siren chirps once, the indicators

flash once, and the LED flashes slowly.

The siren will chirp three times if a door

is open while arming the system.

b. Triggering: The alarm system may

be triggered (except shock sensor) two

seconds after the last door is closed.

The shock sensor is active ten seconds

after the last door is shut.

c. Siren stop: When alarm siren is

sounding, press button #1 to stop the

siren sounding. The alarm will remain

armed. Press the lock button once more to disarm the alarm.

d. Disarm: During the disarm procedure the siren will chirp twice, the

indicators will flash twice and the LED will flash quickly if passive arm is

enabled.

e. Diagnostics: If the alarm has been triggered, when disarming, the siren

will chirp four times and the indicators will flash four times (instead of

twice).

f. Lock/Unlock by remote: if the ignition switch is on, only the central

locking will respond to the remote control.

g. Panic: Hold button #1 for longer than two seconds to sound the siren

and flash the indicators for thirty seconds.

h. Re-arm: The alarm will auto arm & lock the doors in 30 seconds if the

vehicle doors have not been opened since disarming.

BUTTON #2

One Time Mute Arm-Disarm/Car Locator/Boot Release

a. Temporary chirp disable: To disable the siren for one arm/disarm

p r o c e d u r e , p r e s s b u t t o n # 2

momentarily before pressing button

#1. The siren will still chirp three

times if a door is left open.

b. Car locator: Press button #2 for

longer than two seconds while the

alarm is armed to cause the siren to

pulse and the indicators to flash for

five seconds.

c. Boot release: Press button #2 for

longer then two seconds to disarm

the system and open the boot. The

vehicle indicators will flash four times

to confirm boot release signal.

RE-ARM & RELOCK

a. Relock: The alarm will rearm & relock the doors in 30 seconds if no doors

have been opened. This is to prevent accidental disarm.

b. Passive arm: the alarm will automatically arm after 30 seconds if the

ignition is turned off, then the doors are closed. This feature can be

disabled.

c. Passive lock: The alarm will automatically lock the doors 30 seconds

after the ignition is turned off and the last door is closed. This feature can

be enabled. Warning: Strongly recommended not to be used.

d. Anti Hi-jack: When enabled, the alarm will lock the doors four seconds

after the ignition switch is turned on. The alarm will unlock the door

immediately after the ignition is switched off. This feature will not activate

while the door is open.

Special Considerations:

Ensure the interior light of your vehicle is extinguished before

arming the 661. A fading dome light will "trick" the alarm into thinking

one of the doors is open during the arm cycle. An open door

warning is signalled by 3 chirps

PROGRAMMING NEW REMOTE

1. Disarm the alarm by pressing the button #1.

2. Open the driver's door and leave door open.

3. Switch ignition switch Off and On 7 times.

4. When the 7th count is reached, leave ignition switch in the ON position.

5. Vehicle indicators will begin flashing when alarm is ready to accept new

remote codes.

6. Press button #1 on new remote control.

7. Test remotes by arming and disarming the alarm system.

OPTION SETTINGS

Passive Arm / Transmitter Code-Learning / Passive Lock / Ignition

Lock &Unlock / Set Override PIN.

1. Disarm the alarm by pressing button #1.

2. Open the driver's door and leave door open.

3. Turn ignition switch On the number of times corresponding to the feature

you wish to alter. Refer to the Option Table for option selection number.

4. When the correct count is reached, leave ignition switch ON.

5. Vehicle indicators will flash when alarm is ready to change option.

6. Press button #1 on a valid remote control.

7. Alarm will flash vehicle indicators to confirm change, see option table for

one/three flash meaning.

*** Warning this function can result in keys being locked in vehicle!!

Ignition Switches

Feature

Passive arming

Pasive lock

Program new transmitter

Ignition lock /unlock

Set new PIN

EMERGENCY PIN OVERRIDE

In the event a remote is lost, stolen or broken, the #661 may be overridden

by using the programmed two digit Personal Identification Number (PIN).

1. Insert ignition key into vehicle ignition switch.

2. Turn key to the ON position (the position just before engine crank). The

red status LED will glow constantly.

3. Return the key to the ACC position (the first position that powers your

radio).

4. The status LED will begin flashing slowly. Count the flashes.

5. When the flashes match the first number in your PIN, turn the ignition

switch to the ON position again.

6. Repeat step #5 for the second digit of the PIN.

7. The status LED will extinguish and the 661 will now be disarmed and

engine will start.

PROGRAMMING NEW PIN

1. Disarm the alarm by pressing button #1.

2. Open the driver's door and leave door open.

3. Switch ignition switch Off and On 9 times.

4. When the 9th count is reached, leave ignition switch ON.

5. Vehicle indicators will flash when alarm is ready accept new remote

PIN.

6. Press button #1 the number of times corresponding to the first digit of

the new PIN. Press button #2 the number of times corresponding to the

second digit of the new PIN.

7. Alarm will flash vehicle indicators three times to confirm successful

programming.

*** All central locking and boot release features require additional

hardware, which is not supplied with the 661 alarm system. Vehicles with

central locking and/or electronic boot release will still require connections

to the 661 which are not a part of a standard installation.

One flash Three flashes

Disabled

Enabled

Disabled

Enabled

Press new remote control

Disabled

Enabled

Begin changing PIN