AutomationDirect IRON HORSE GSD5-240-10N4-A 사용자 설명서 - 페이지 15

{카테고리_이름} AutomationDirect IRON HORSE GSD5-240-10N4-A에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. AutomationDirect IRON HORSE GSD5-240-10N4-A 16 페이지.

페이지 인쇄

GSD5 Series Accessories

GSDA-AI-V5

Optional analog voltage or current input card for open-frame GSD5-240-10C series DC drives only

This option card allows for the use of either a grounded or non-grounded remote DC signal such as

0–5 VDC through 0–250 VDC, 4–20mA, or a remote speed potentiometer. The DC input signal type can

be selected for voltage (V

(P4) selection that should be set to the (Lo) setting when using a 4–20mA signal or voltage ranges of

0–5 VDC through 0–25 VDC. When using voltage ranges of 0–25 VDC through 0–250 VDC, this jumper

must be set to (Hi). The GAIN trim pot is used to set full linear output in reference to the input signal

range. The output of this remote signal isolation board is a linear signal that is proportional to the

remote input signal being supplied.

GSDA-AI-V5 Mounting and Wiring Diagram

MIN

JU2

ORANGE

JU3

JU1

GSD5-240-10C with

GSDA-AI-V5 installed

GSDA-AI-V5 Setup Procedure

1) With motor connected and NO power at the drive, connect a DC voltmeter (meter must not be

grounded) to control outputs as follows: Meter COMMON to the -ARM terminal; Meter POSITIVE

to the +ARM terminal Select correct meter range (0-90V or 0-180V)

2) Preset GAIN trim pot (analog voltage follower board) fully CCW, place range jumper clip in proper

position

3) Preset control as follows: MIN and IR COMP fully CCW; MAX at 50%

4) Apply desired AC voltage to drive and analog voltage follower board

5) With 0 volts into analog voltage follower board, adjust MIN trim pot on drive to eliminate

deadband To do this, increase MIN fully CW, and then adjust CCW until meter reads 0V

6) Apply maximum input voltage to analog voltage follower board input

7) Adjust GAIN until no further change in voltage output occurs, then turn CCW until a 5V drop

occurs, and then set control MAX to 90VDC (for 120V input) or 180VDC (for 240V input)

8) For Closed Loop systems the IR COMP should remain fully CCW For Open Loop systems, set IR

per set-up procedure

9) Some interaction between trimpots may occur Recheck the MIN trim pot setting and repeat steps 5

through 7 as needed

IronHorse GSD5 DC Drives User Manual – 1st Ed, Rev E – 05/13/2020

) or current (4–20mA) via the JP2 jumper clip. There is a Hi/Lo range jumper

MAX

ACCEL

IR COMP

Vin or 4-20mA

CONNECTOR

RANGE

JUMPER

GAIN

CONNECTOR

TRIMPOT

-1

4-20

-2

-3

Vin

-1

-2

-3

JP2

-ARM

+ARM

AC1

AC2

CUSTOMER

COMMON

SIGNAL

CUR LIM

The Kit Includes:

• (1) option card

• (3) spacers (025 x 05 in)

• (3) Phillips-head screws (#6-32 x 075

Spacers:

Install spacers at JU1, JU3, and JU5, as

illustrated.

JU4

Wiring Jumpers:

Connect wires JU2 and JU4 as

JU5

illustrated.

in)

Page 15