2gig Technologies 2GIG-TS1 설치 지침

{카테고리_이름} 2gig Technologies 2GIG-TS1에 대한 설치 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. 2gig Technologies 2GIG-TS1 2 페이지. Touch screen wireless keypad

페이지 인쇄

2GIG-TS1

Touch Screen

Wireless Keypad

For Remote Control of

the 2GIG Security System

Installation Instructions

WALL MOUNTING THE KEYPAD

USE THE THREE SCREWS AND

ANCHORS SUPPLIED TO ATTACH

THE MOUNTING PLATE TO THE WALL

ROUTE 18 AWG WIRE

BETWEEN THE KEYPAD

AND THE POWER SUPPLY

LOCATION

WIRE GAUGE CHART

GAUGE

MAXIMUM RUN

100 FEET

150 FEET

USE UN-SHIELDED 2-CONDUCTOR

INSTALL POWER SUPPLY

POWER

SUPPLY

POWER

SUPPLY

BRACKET

INSTALLED

FOR STANDARD

STYLE OUTLET

BRACKET

INSTALLED

FOR DECORA

STYLE OUTLET

PRODUCT DESCRIPTION

The Model 2GIG-TS1 Touch Screen Wireless Keypad is a remote control device

designed for the 2GIG security system Control Panel. The keypad supports all

operating and emergency functions of the system. The keypad is designed for

indoor use only.

The front panel

and

buttons serve as controls as well as indicators.

Pressing the

button displays emergency icons on the display for Panic, Fire,

and Emergency alarm activation (each has programmable options and can be

enabled or disabled). Pressing the

button changes the system display to the

Home Screen. The keypad is powered from a plug-in power supply (included).

The 2GIG-TS1 exchanges information through a secure 2-way wireless connection

with the Control Panel. Before operation the keypad must be "paired" with the

Control Panel. Refer to the Control Panel's installation instructions for details on

pairing the keypad to the Control Panel.

CONNECT POWER WIRES TO KEYPAD

RE-CONNECT THE

USE #6 INSULATED SPADE

HANGING STRAP

TERMINALS (NOT SUPPLIED)

TO CONNECT WIRES FROM

THE POWER SUPPLY TO

THE KEYPAD

OBSERVE

POLARITY !!!

PAIR KEYPAD WITH CONSOLE & TEST

PLACE THE CONSOLE IN

PROGRAMMING MODE

AND PREPARE IT FOR ENROLLING

THE WIRELESS KEYPAD

2GIG CONSOLE

REFER TO THE CONSOLE'S

INSTALLATION INSTRUCTIONS

FOR DETAILS ON PROGRAMMING

AND TESTING THE WIRELESS KEYPAD

WHEN LEARN IS PRESSED ON

THE CONSOLE, AND PAIR WITH PANEL

IS PRESSED ON THE TS1, THE TWO

TS1 WIRELESS

UNITS WILL COMMUNICATE AND

KEYPAD

AUTOMATICALLY ENROLL THE KEYPAD

KEYPAD PREPARATION

FLIP OPEN THE BACK COVER

LOOSEN CASE SCREW

OF THE KEYPAD

FOUR TURNS

THE BACK COVER IS USED

AS THE KEYPAD'S MOUNTING PLATE

DISCONNECT THE

HANGING STRAP

CLOSE KEYPAD

SNAP CASE CLOSED

TIGHTEN CASE SCREW

LIMITED WARRANTY

This 2gig Technologies Inc. product is warranted against defects in material

and workmanship for twelve (12) months. This warranty extends only to

wholesale customers who buy through 2gig Technologies Inc. authorized

distribution channels. 2gig Technologies Inc. does not warrant this product to

consumers. Consumers should inquire from their selling dealer as to the nature

of the dealer's warranty, if any. There are no obligations or liabilities on the

part of 2gig Technologies Inc. for consequential damages arising out of

or in connection with use or performance of this product or other indirect

damages with respect to loss of property, revenue, or profit, or cost of

removal, installation, or reinstallation. All implied warranties, including implied

warranties for merchantability and implied warranties for fitness, are valid only until

the warranty expires. This 2gig Technologies Inc. Warranty is in lieu of all other

warranties express or implied.

LOCATING THE KEYPAD

SELECT A LOCATION FOR THE KEYPAD,

BE SURE THAT AC POWER IS AVAILABLE NEARBY,

WATCH OUT FOR STUDS, ELECTRICAL, & PIPES IN THE WALL

USE THE KEYPAD'S BACK COVER AS A TEMPLATE

TO MARK THE THREE SCREW HOLES AND THE

POWER WIRING ACCESS HOLE

USE A DRYWALL SAW TO CUT THE WIRING HOLE

CONNECT POWER SUPPLY

POWER

SUPPLY

CONNECT POWER

WIRES TO THE

POWER SUPPLY

OBSERVE

RIGHT

PROPER

TERMINAL

POLARITY !!!

- 14 VDC

LEFT

TERMINAL

18 AWG / 2-CONDUCTOR

+ 14 VDC

TO KEYPAD

IMPORTANT !!!

Radio controls provide a reliable communications link and fill an important need

in portable wireless signaling. However, there are some limitations which must be

observed.

 For U.S. installations only: The radios are required to comply with FCC Rules and

Regulations as Part 15 devices. As such, they have limited transmitter power and

therefore limited range.

 A receiver cannot respond to more than one transmitted signal at a time and may be

blocked by radio signals that occur on or near their operating frequencies, regardless of

code settings.

 Changes or modifications to the device may void FCC compliance.

 Infrequently used radio links should be tested regularly to protect against undetected

interference or fault.

 A general knowledge of radio and its vagaries should be gained prior to acting as a

wholesale distributor or dealer, and these facts should be communicated to the ultimate

users.

This device complies with FCC Part 15 and Canada Rules and Regulations.

Operation is subject to the following two conditions: (1) This device may not cause

harmful interference and (2) this device must accept any interference received,

including interference that may cause undesired operation.