Celestron 44124 사용 설명서 - 페이지 2

{카테고리_이름} Celestron 44124에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Celestron 44124 17 페이지. Basic microscope kit
Celestron 44124에 대해서도 마찬가지입니다: 사용 설명서 (10 페이지), 빠른 설정 매뉴얼 (13 페이지)

페이지 인쇄

Standard acceSSorIeS

wIth your MIcroScope

• WF 10x Eyepiece

• 4x, 10x, 40x (spring loaded)

Objective Lenses

• Top Illuminator – LED with

Adjustable Brightness

• Bottom Illuminator – LED with

Adjustable Brightness

• Needle Probe and Eyedropper

• WF 16x Eyepiece

• Filter Wheel/Diaphragm – 6 Positions

• 8 Prepared Slides and 4 Blank Slides

• 4 Cover Slips

• Tweezers

MagnIfIcatIon tabLe

Use the following table to determine magnification using your microscope's

different eyepiece/objective lens combinations.

objective lenS

WF 10x Eyepiece

WF 16x Eyepiece

SettIng up MIcro360

1. remove Styrofoam container from carton.

2. carefully remove microscope and accessories from

container and set on a table, desk or other flat surface.

3. remove bag covering the microscope.

4. remove cap from eyepiece tube.

5. install four aa batteries (user supplied) under the

microscope's base (see images below).

6. insert the WF 10x eyepiece in the eyepiece tube.

MIcro360 operatIon

Before viewing specimens, please read these sections thoroughly regarding

focusing, changing power (magnification), using the stage and adjusting

illumination.

rotatIng the head

Your microscope's head can be rotated 360°. You can view from any

position by moving the head (while holding the arm) to a desired location.

objective lens

10x

40x

100x

64x

160x

eyepiece

eyepiece tube

nosepiece

Stage

bottom

illuminator

VIewIng a SpecIMen

Carefully place a specimen slide under the stage clips and center the

specimen. Images will be observed upside down and reversed right to

left, with practice centering objects will become easier to accomplish.

Prepared slides, blank slides and tools are included with your microscope

40x

to get you started (see images below).

400x

You are now ready to focus and view a specimen. Be careful not to damage a

640x

specimen slide or valuable object. When using higher powers while focusing,

make sure the objective lens does not hit the slide or object being viewed.

focuSIng & changIng power (MagnIfIcatIon)

Place specimen slide (or object) directly under the objective lens and use

the focus knob to focus on the specimen. For smaller objects, place on a

flat material for easier viewing.

1. Always start with lowest power (4x objective lens and WF 10x eyepiece).

This objective lens and eyepiece combination will yield 40x – the lowest

but most useful power for viewing large or small solid objects.

2. For higher powers, rotate the nosepiece to change the objective lens to

10x or 40x. Hold the microscope above the nosepiece with one hand

and rotate the nosepiece with the other hand until it clicks in position.

Be cautious not to let the objective lens touch the specimen slide or

object when changing to higher powers. Note: You should first turn the

focus knob to lower the stage.

3. You can replace the WF 10x eyepiece with the WF 16x eyepiece to

obtain three additional magnifications, including the highest power

possible (640x).

Head

arm

top

illuminator

Stage clips

Focus Knob

base

bottom

illuminator

Switch

celestron

www.

.com