2gig Technologies 2GIG-TS2-E 설치 지침 - 페이지 2

{카테고리_이름} 2gig Technologies 2GIG-TS2-E에 대한 설치 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. 2gig Technologies 2GIG-TS2-E 2 페이지. Wireless touch screen keypad

페이지 인쇄

Verifying the Firmware Version on Both Devices

In order to communicate properly, the keypad and the control panel must be running the same

firmware version.

NOTE: If the keypad has not yet been paired to the control panel, the firmware version number

displays on the keypad's main screen.

To check the firmware version on the keypad and control panel (after they have been paired):

Press the Home

button.

At the Home screen, tap Security.

Tap Menu.

Tap Toolbox.

At the Enter Your Code to Access the Toolbox screen, enter the master code.

At the Toolbox (1 of 3) screen, tap → to scroll to the Toolbox (2 of 3) screen.

Tap Version.

At the Version screen, ensure the Firmware Version field matches on both the control panel

and keypad.

Updating the Firmware

To update the firmware on the keypad, you will need:

●

The Firmware Update Cable for the TS2 and Control Panel (2GIG-UPCBL2).

●

To download the latest firmware update go to dealer.2gig.com.

Firmware update available at www.2gig.com/dealers.

Programming the Keypad to the Control Panel

To communicate with up to four (4) Wireless Touch Screen Keypads, you must install the 900 MHz

Transceiver Module in the control panel before using the programming steps below. See above Minimum

Requirements for information on which XCVR module is required.

To program the keypad into the control panel:

Connect the AC Adapter to the keypad as described in Connecting the Power to the Keypad.

Power ON the keypad. The This Device is Not Paired with a Control Panel message appears on the

keypad's screen.

Ensure the control panel is powered ON. Then tap the Home

Tap the logo in the lower-right corner of the control panel Home screen.

At the Enter Your Code screen, enter your four (4)-digit installer code.

At the Installer Toolbox (page 1 of 2) screen, tap System Configuration.

At the Q1: Select RF Sensor # (01 to 48) screen, tap Go To.

At the Enter Question Number (2 Digits) screen, enter 04.

At the Q4: Select RF Keypad # (1 to 4) screen, tap → to scroll to the desired keypad number (1-4).

For example, tap → to scroll to (1) keypad one. Then tap ↓.

10 At the Q: Select RF Keypad # Used (0 to 1) screen, tap → to scroll to (1) Enabled. Then tap ↓.

11 At the Q: Select RF Keypad # Equipment Code screen, tap → to scroll to (1059) 2GIG-TS2 Wireless

Touch Screen Keypad. Then tap ↓.

12 At the Q: RF Keypad # Keypad ID (Read-Only) screen, press the Learn button. This places the

control panel into learning mode.

13 On the control panel at the Pair with Xcvr Device screen, the "initiating learning process"

message appears.

14 On the keypad, at the This Device is Not Paired with the Control Panel screen, tap Pair with Panel.

This places the keypad into learning mode.

When the "learn operation succeeded" message appears on both the control panel and keypad, the

devices are linked.

15 Ensure the following is true:

●

On the control panel at the Pair with Xcvr Device screen, ensure the Type reads 2GIG-TS2-E

Wireless Touch Screen Keypad and that the ID# appears. Tap OK.

●

On the keypad at the Pair with Panel screen, ensure that the Network ID shows a unique

hexadecimal number for the control panel and that the Keypad ID number appears. Tap OK.

16 On the control panel at the Pair with Xcvr Device screen, tap OK. Then tap ↓.

NOTE: The keypad displays a "The Security System is Temporarily Not Operational" message and

remains in this state until you finish programming the device into the panel, save the changes, and exit

out of programming mode.

17 At the Q: RF Keypad # Keypad ID (Read-Only) screen, ensure the keypad ID appears. Then tap ↓.

18 At the Q: Select RF Sensor # Equipment Age screen, tap → to select one of the following:

●

(0) New (Default). Then tap ↓.

●

(1) Existing. Then tap ↓.

19 At the Q: Construct RF Sensor # Voice Descriptor screen, the voice descriptor keypad one (or

keypad two, keypad three, and so on) should display.

If you want to change the voice descriptor, tap the delete (X) button. Then tap Insert, then enter the

appropriate voice descriptor code. For example, to create a voice descriptor code named keypad

one, do the following:

●

Tap Insert. Then enter 123 for keypad.

●

Tap Insert. Then enter 161 for one. Then tap ↓.

TIP: For a complete list of available voice descriptors, see the control panel's Quick Programming Guide.

20 At the Summary of RF Keypad # screen, tap Skip.

21 At the Q5: Enter Exit Delay, in Seconds (45-120) screen, enter the desired exit delay. The default

value is 60. The tap End. This setting affects both the control panel and keypad.

22 At the Summary of System Configuration screen, tap Save Changes and ensure a check mark

appears in the Save Changes box. Then tap Exit. This restarts the control panel.

NOTE: You can program up to four (4) keypads into the control panel by repeating the steps above.

Disabling a Keypad from the Control Panel

If you want to disable a keypad after programming it into the control panel:

Ensure the control panel is powered ON. Then tap the Home

Tap the logo in the lower-right corner of the control panel Home screen.

At the Enter Your Code screen, enter your four (4)-digit installer code to go to the Installer Toolbox

(page 1 of 2) screen.

At the Installer Toolbox (1 of 2) screen, tap System Configuration.

At the Q1: Select RF Sensor # (01 to 48) screen, tap Go To.

At the Enter Question Number (2 Digits) screen, enter 04.

At the Q4: Select RF Keypad # (1 to 4) screen, tap → to scroll to the keypad number (1-4) to

remove. For example, tap → to scroll to (1) keypad one. Then tap ↓.

At the Q: Select RF Keypad # Used screen, tap → to scroll to (0) Disabled. Then tap ↓.

Tap ↓ until the Summary of RF Keypad # screen appears. Then tap Skip.

10 At the Q5: Enter Exit Delay, in Seconds (45-120) screen, tap End.

11 At the Summary of System Configuration screen, tap Save Changes and ensure a check mark

appears in the Save Changes box. Then tap Exit. This restarts the control panel.

Restoring the Keypad's Factory Settings

To restore the keypad's factory settings to use it with a different control panel:

Power OFF and then power ON the keypad.

Press and hold down both the Emergency

When both buttons illuminate, the keypad's factory settings have been restored. The screen will

display the following message: "This Device is Not Paired with a Control Panel."

button.

and Home

buttons for approximately 20 seconds.

SPECIFICATIONS

Wireless Signal Range

500 ft (152.4 m), open air, with Wireless Control Panel

Transceiver

Silicon Labs SI1001-E-GM2

Transmitter Frequency

900 MHz frequency-hopping bi-directional communication

25 channel frequency-hopping spread spectrum, 403 kHz channel spacing (910.2-

Radio

920.275 MHz), GFSK modulation, 128 kbps, +19dBm maximum RF power out

Dimensions (L x W x H)

4.3" x 6.7" x 0.8" (11 x 17 x 2 cm)

Weight (including battery)

9.6 oz.

Housing Material

ABS Plastic

Color

White

Operating Temperature

32°-120 F° (0°-49° C)

Relative Humidity

5-95% Non-Condensing

Operating Voltage

14VDC

Certification

FCC, Industry Canada

REGULATORY INFORMATION

Wireless Product Notice

Radio controls provide a reliable communications link and fill an important need in portable wireless

signaling; however, there are some limitations which must be observed.

●

For United States Installations Only: The radios are required to comply with FCC Rules and

Regulations as Part 15 devices. As such, they have limited transmitter power and therefore

limited range (approximately 400 ft.).

●

A receiver cannot respond to more than one transmitted signal at a time and may be blocked by

radio signals that occur on or near their operating frequencies, regardless of code settings.

●

Changes or modifications to the device may void FCC compliance.

●

Infrequently used radio links should be tested regularly to protect against undetected interference

or fault.

●

A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale

distributor or dealer, and these facts should be communicated to the end users.

FCC Notice

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference, and

This device must accept any interference received, including interference that may cause

undesired operation.

This equipment has been tested and found to comply with the limits for Class B Digital Device, pursuant

to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

●

Reorient or relocate the receiving antenna

●

Increase the separation between the equipment and receiver

●

Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected

●

Consult the dealer or an experienced radio/TV technician for help

Any changes or modifications not expressly approved by the party responsible for compliance could void

the user's authority to operate the equipment.

Industry Canada Notices

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the

following two conditions: (1) this device may not cause interference, and (2) this device must accept any

interference, including interference that may cause undesired operation of the device.

Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated

by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions,

may give the telecommunications company cause to request the user to disconnect the equipment.

Users should ensure for their own protection that the electrical ground connections of the power

utility, telephone lines and internal metallic water pipe system, if present, are connected together. This

precaution may be particularly important in rural areas.

WARNING: Users should not attempt to make such connections themselves, but should contact the

appropriate electric inspection authority, or electrician, as appropriate.

Operating and Storage Temperature

The recommended storage temperature for all touchscreens is -10°C to 60°C (14°F to 140°F).

For optimal touchscreen use, operational temperature is 0°C to 49°C (32°F to 120°F).

LIMITED WARRANTY

This Nortek Security & Control LLC product is warranted against defects in material and workmanship

for one (1) year. This warranty extends only to wholesale customers who buy direct from Nortek Security

& Control LLC or through Nortek Security & Control LLC's normal distribution channels. Nortek Security

& Control LLC does not warrant this product to consumers. Consumers should inquire from their selling

dealer as to the nature of the dealer's warranty, if any.

THERE ARE NO OBLIGATIONS OR LIABILITIES ON THE PART OF NORTEK SECURITY &

CONTROL LLC FOR CONSEQUENTIAL DAMAGES ARISING OUT OF OR IN CONNECTION

WITH USE OR PERFORMANCE OF THIS PRODUCT OR OTHER INDIRECT DAMAGES

WITH RESPECT TO LOSS OF PROPERTY, REVENUE, OR PROFIT, OR COST OF REMOVAL,

INSTALLATION, OR REINSTALLATION. ALL IMPLIED WARRANTIES FOR FUNCTIONALITY, ARE

VALID ONLY UNTIL THE WARRANTY EXPIRES. THIS NORTEK SECURITY & CONTROL LLC

WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED.

All products returned for warranty service require a Return Authorization Number (RA#). Contact Returns

at 1-855-546-3351 for an RA# and other important details.

For technical support in the USA and Canada: 855-2GIG-TECH

(855-244-4832)

Contact: https://www.nortekcontrol.com/technical-support/

Visit www.nortekcontrol.com for technical support hours of operation.

For technical support outside of the USA and Canada: Contact your

regional distributor.

Visit www.2gig.com/dealers/ for a list of distributors in your region.

Nortek Security & Control LLC | 2GIG

5919 Sea Otter Place, Suite 100

Carlsbad, CA 92010 USA

of Nortek Security & Control LLC. All other company and product names used herein may

be trademarks, or registered trademarks of the respective companies.

10032360 Rev-B