dB Technologies B-HYPE 8 빠른 시작 사용 설명서 - 페이지 4
{카테고리_이름} dB Technologies B-HYPE 8에 대한 빠른 시작 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. dB Technologies B-HYPE 8 4 페이지.
페이지 인쇄
Technical Data
Speaker
Type:
2-way active speaker
Usable Bandwidth [-10
dB]:
Frequency Response [-6
dB]:
Max SPL (1
m):
120 dB
HF compression
driver:
1 " Exit
HF voice
coil:
1"
LF:
8"
LF Voice
Coil:
1.5"
Crossover
frequency:
2300 Hz (24 dB/oct.)
Horizontal
dispersion:
asymmetrical 85° up / 120° down
Vertical
dispersion:
85° (+25°/ -60°)
Amplifier
Amp
Technology:
Custom made
Amp
Class:
Class-D – Passive cooling (convection)
RMS
Power:
130 W
Operating voltage (
factory set
220-240V~ (50-60Hz) or
110-120V~ (50-60 Hz)
Scan with your QR Reader
App to download the
complete User Manual
EMI CLASSIFICATION
According to the standards EN 55103 this equipment is designed and suitable to operate in E3 (or lower E2, E1) Electromagnetic environments.
FCC CLASS B STATEMENT ACCORDING TO TITLE 47, PART 15, SUBPART B, §15.105
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the
equipment.
WARNING: Make sure that the loudspeaker is securely installed in a stable position to avoid any injuries or damages to persons or properties.
For safety reasons do not place one loudspeaker on top of another without proper fastening systems. Before hanging the loudspeaker check
all the components for damages, deformations, missing or damaged parts that may compromise safety during installation. If you use the
loudspeakers outdoor avoid spots exposed to bad weather conditions.
Contact dB Technologies for accessories to be used with speakers. dBTechnologies will not accept any responsibility for damages caused by
inappropriate accessories or additional devices.
Features, specification and appearance of products are subject to change without notice.
dBTechnologies reserves the right to make changes or improvements in design or manufacturing without assuming any obligation to change
or improve products previously manufactured.
B-HYPE 8
65 – 20000 Hz
70 – 19600 Hz
):
www.dbtechnologies.com
Processor and user interface
Controller:
28/56 bit
Limiter:
Peak, Thermal, RMS
Controls:
Volume, Audio Input Sensitivity, DSP preset
Input / Output
Mains
connection:
Signal
Input:
Signal
Out:
(Balanced) 1x XLR OUT (LINK)
Mechanics
Housing:
Polypropylene
Grille:
Full metal grille
Handles:
3 (2 on sides 1 on top)
Pole
Mount:
Yes, 36 mm
Width:
243 mm (9.57 in)
Height:
443 mm (17.44 in)
Depth:
231 mm (9.09 in)
Weight:
6.6 kg (14.55 lbs.)
Download the complete user manual from the site:
www.dbtechnologies.com/EN/Downloads.aspx
-
48 kHz
VDE
(Balanced) 1x Combo IN (MIC/LINE)
Rev 1.3 cod. 420120254Q