Automationdirect.com SOLO SL4896 Series 빠른 시작 가이드 - 페이지 3

{카테고리_이름} Automationdirect.com SOLO SL4896 Series에 대한 빠른 시작 가이드을 온라인으로 검색하거나 PDF를 다운로드하세요. Automationdirect.com SOLO SL4896 Series 4 페이지.

페이지 인쇄

Automationdirect.com SOLO SL4896 Series 빠른 시작 가이드

11-2

Voltage Input

1. Access the Initial Setup mode by pressing and holding the

inpt

, use the

and

buttons to select the value that corresponds to the voltage input that will be

applied to the controller. See the table for voltage specifications. Press the

value. The controller will display the module information splash screen for three seconds and then return to

the main screen.

2. Press the

;

button for three seconds again. Press the

Use the

and

buttons to select the high engineering value that corresponds to the maximum voltage

signal that will be applied to the input of the controller. For example, if the

is the value the controller will display when the input equals 5V. Press the

value. Press the

•

button to access the parameter

low engineering value that corresponds to the minimum voltage signal that will be applied to the input of the

controller. For example, if the

0V-5V input is to be used, this is the value the controller will display when the

input equals 0V. Press the

;

button twice to save the selected value and return to the controller main screen.

3. Press the

•

button repeatedly until the parameter

to indicate the position of the decimal point for the PV and SV values on the controller. Press the

;

button twice to save the selected value and return to the controller main screen.

4. If the voltage input PV value displayed on the controller needs to be adjusted, press the

than 3 seconds. Press the

•

button repeatedly until the parameter

buttons to adjust a positive or negative offset to the PV value displayed on the controller. Press the

twice to save the selected value and return to the controller main screen.

Voltage Input Type and Input Range

Voltage Input Type

0~50mV Analog Input

0V~10V Analog Input

0V~5V Analog Input

11-3

Current Input

1. Install the supplied 249 ohm resistor between terminal #9 and #10.

2. Access the Initial Setup mode by pressing and holding the

inpt

, use the

and

buttons to select the value that corresponds to the current input that will be

applied to the controller. See the table for current specifications. Press the

value. The controller will display the module information splash screen for three seconds and then return to the

main screen.

3. Press the

;

button for three seconds again. Press the

appears. Use the

and

buttons to select the high engineering value that corresponds to the maximum

current signal that will be applied to the input of the controller. For example, if the

used, this is the value the controller will display when the input equals 20mA. Press the

the selected value. Press the

•

button to access the parameter

to select the low engineering value that corresponds to the minimum current signal that will be applied to the

input of the controller. For example, if the

ma4

4-20mA input is to be used, this is the value the controller will

display when the input equals 4mA. Press the

;

controller main screen.

4. Press the

•

button repeatedly until the parameter

to indicate the position of the decimal point for the PV and SV values on the controller. Press the

;

button twice to save the selected value and return to the controller main screen.

5. If the current input PV value displayed on the controller needs to be adjusted, press the

than 3 seconds. Press the

•

button repeatedly until the parameter

buttons to adjust a positive or negative offset to the PV value displayed on the controller. Press the

twice to save the selected value and return to the controller main screen.

Current Input Type and Range

Current Input Type

4~20mA Analog Input

0~20mA Analog Input

12-1

PID Control Setup

Note: Select the desired control mode before beginning PID Control Setup.

There are four groups for storing PID parameters,

less than three seconds and press the

•

button repeatedly until the parameter

and

buttons to select which group to use for storing the PID parameters. Press the

confirm the setting. The groups

pid0

pid3

in the control process. If the group

pid4

is selected, the controller will automatically select the most useful

PID parameters based on the current temperature setting and the SV value set in each PID group.

The parameters for PID can be auto-tuned using the

;

button for less than three seconds. Use the

button to save the value. Optimal PID values are automatically determined with the auto-tune feature. PID

operation can also be controlled by programming the individual

Access these parameters by pressing the

;

button for less than three seconds and press the

repeatedly until the parameter

appears where

the

and

buttons to change the value for the Proportional band if desired and press the

save the value. Press the

•

button to access the

the value for the Integral time if desired and press the

access the

parameter. Use the

and

and press the

;

button twice to save the value and return to the controller main screen.

12-2

Heating Loop with PID Control

1. Access the Initial Setup mode by pressing and holding the

button repeatedly until the parameter

Ctrl

appears. Confirm the default value

control. Press the

•

button to access the parameter

ed for controlling a heating loop. Press the

;

button to return to the controller main screen.

2. Press the

•

button to access the parameter

the

;

button to return to the controller main screen.

3. Refer to Section 12-1 of this Quick Start Guide to set up the PID control parameters.

4. If the temperature controller's output #1 is discrete, access the regulation mode again by pressing the

button for less than three seconds. Press the

•

the

and

buttons to set the time period in seconds for the heating control. Press the

to save the value and return to the controller main screen.

All manuals and user guides at all-guides.com

;

button for three seconds. In the parameter

;

button to save the selected

•

button to access the parameter

0V-5V input is to be used, this

;

button to save the selected

tp-l

. Use the

and

buttons to select the

appears. Use the

and

buttons to select

;

button for less

tpof

appears. Use the

;

LED Display

Engineering Range

-999 ~ 9999

v10

-999 ~ 9999

;

button for three seconds. In the parameter

;

button to save the selected

•

button repeatedly until the parameter

ma4

4-20mA input is to be

;

button to save

tp-l

. Use the

and

button twice to save the selected value and return to the

appears. Use the

and

buttons to select

;

button for less

tpof

appears. Use the

;

LED Display

Engineering Range

-999 ~ 9999

ma4

-999 ~ 9999

ma0

pid0

(PID0) -

pid3

(PID3). Press the

;

pid0

appears. Use the

;

can be individually set up with different SV values to be used

parameter. Access this parameter by pressing the

button to turn the auto-tune feature

. Press the

, and

parameters for each PID group.

•

corresponds to the PID group you are programming. Use

;

parameter. Use the

and

buttons to change

;

button to save the value. Press the

•

buttons to change the value for the Derivative time if desired

;

button for three seconds. Press the

Pid

is selected for PID

s-hC

Confirm the default value

heat

r-s

. Verify that the default value

run

is selected. Press

button repeatedly until the parameter

htpd

appears. Use

;

button twice

12-3

Heating Loop with ON / OFF Control

1. Access the Initial Setup mode by pressing and holding the

button repeatedly until the parameter

/ OFF control. Press the

;

button to save the value. Press the

Confirm the default value

heat

the control

ler main screen.

2. Press the

•

button to access the parameter

tp-h

the

;

button to return to the controller main screen.

3. Press the

;

button for less than three seconds to access the parameter

buttons to enter hysteresis. This is the amount the PV must go below the SV before the controller output turns

on. Press the

;

button twice to save the selected value and return to the controller main screen.

12-4

Cooling Loop with PID Control

1. Access the Initial Setup mode by pressing and holding the

button repeatedly until the parameter

control. Press the

•

button to access the parameter

controlling a cooling loop. Press the

and

2. Press the

•

button to access the parameter

button

the

;

button to return to the controller main screen.

3. Refer to Section 12-1 of this Quick Start Guide to set up the PID control parameters.

4. If the temperature controller's output #1 is discrete, access the regulation mode again by pressing the

button for less than three seconds. Press the

the

and

buttons to set the time period in seconds for the cooling control. Press the

to save the value and return to the controller main screen.

12-5

Cooling Loop with ON / OFF Control

1. Access the Initial Setup mode by pressing and holding the

button repeatedly until the parameter

/ OFF control. Press the

;

button to save the value. Press the

Use the

button to select

Cool

value and return to the controller main screen.

2. Press the

•

button to access the parameter

the

;

button to return to the controller main screen.

3. Press the

;

button for less than three seconds to access the parameter

buttons to enter hysteresis. This is the amount the PV must go above the SV before the controller output turns

tp-h

on. Press the

;

button twice to save the selected value and return to the controller main screen.

12-6

Dual Heating / Cooling Loop with PID Control

buttons

1. Access the Initial Setup mode by pressing and holding the

button repeatedly until the parameter

control. Press the

•

button to access the parameter

controlling a dual heating / cooling loop. This parameter sets the heating control to output #1 and the cooling

control to output #2. Press the

;

2. Press the

•

button to access the parameter

the

;

button to return to the controller main screen.

3. Refer to Section 12-1 of this Quick Start Guide to set up the PID control parameters.

4. If the temperature controller's output #1 is discrete, access the regulation mode again by pressing the

and

button for less than three seconds. Press the

button

the

and

buttons to set the time period in seconds for output #1, the heating control. Press the

button to save the value. If the temperature controller's output #2 is discrete, press the

until the parameter

hCpd

appears. Use the

output #2, the cooling output. Press the

screen.

5. Optional regulation parameters can be programmed for a second control

output. If this is desired, access the regulation mode again by pressing the

;

button for less than three seconds. Press the

until the parameter

Coef

appears. This value allows the cooling control

to have a different proportional setting than the heating loop. The heating

loop proportional band setting is multiplied by the

a proportional band setting for the cooling loop control. Use the

buttons to change this value if desired. Press the

save the selected value. Press the

button for

dead

. Use the

and

around the setpoint where the output is not effected by the proportional

button to

control value. As long as the PV remains within the deadband zone the

output is not affected by the proportional control. The integral and deriv-

ative controls ignore the deadband setting and may cause the output to

be on within the deadband zone. Press the

value and return to the controller main screen.

;

12-7

Dual Heating / Cooling Loop with ON / OFF Control

1. Access the Initial Setup mode by pressing and holding the

button

button repeatedly until the parameter

ON / OFF control and press the

button to

parameter

s-hC

. Use the

sets the heating control to output #1 and the cooling control to output #2. Press the

button to

the value and return to the controller main screen.

2. Press the

•

button to access the parameter

the

;

button to return to the controller main screen.

3. Press the

;

button for less than three seconds to access the

parameter

hts

. Use the

for output #1, the heating control. This is the amount the PV must go

below the SV before the controller output turns on. Press the

•

button to save the selected value. Press the

the parameter

Cts

. Use the

is select-

esis for output #2, the cooling control. This is the amount the PV

must go above the SV before the controller output turns on. Press

the

;

button twice to save the selected value and return to the

controller main screen.

4. Optional regulation parameters can be programmed for additional dual loop control. If this is desired, access

;

the regulation mode again by pressing the

repeatedly until the parameter

dead

value around the setpoint where the output is not on. The PV must go beyond the deadband range in order for

either the heating or cooling output to turn on. Press the

to the controller main screen.

;

button for three seconds. Press the

Ctrl

appears. Use the

and

buttons to select

•

button to access the parameter

is selected for controlling a heating loop. Press the

r-s

. Verify that the default value

hts

;

button for three seconds. Press the

Ctrl

appears. Confirm the default value

s-hC

. Use the

;

button twice to save the value and return to the controller main screen.

r-s

. Verify that the default value

•

button repeatedly until the parameter

;

button for three seconds. Press the

Ctrl

appears. Use the

and

buttons to select

•

button to access the parameter

for controlling a cooling loop. Press the

;

r-s

. Verify that the default value

Cts

;

button for three seconds. Press the

Ctrl

appears. Confirm the default value

s-hC

. Use the

button twice to save the value and return to the controller main screen.

r-s

. Verify that the default value

•

button repeatedly until the parameter

and

buttons to enter the cycle period in seconds for

button twice to save the value and return to the controller main

;

Output

•

button repeatedly

Heating

Coef

value to create

Dual control with PID

and

;

button to

•

button to access the parameter

Output

buttons to enter a deadband zone value

Heating

Dual control with PID

;

button twice to save the

;

button for three seconds. Press the

Ctrl

appears. Use the

and

buttons to select

;

button to save the selected value. Press the

button to select

h1C2

for controlling a cooling / heating loop. This parameter

r-s

. Verify that the default value

and

buttons to enter hysteresis

hts

Heating hysteresis

;

•

button to access

Heating

and

buttons to enter hyster-

OFF

Dual loop ON / OFF control

output operation

;

button for less than three seconds. Press the

appears. Use the

and

buttons to enter a deadband zone

;

button twice to save the selected value and return

•

onof

for ON

s-hC

button to return to

;

run

is selected. Press

. Use the

and

•

Pid

is selected for PID

button to select

Cool

for

run

is selected. Press

;

Clpd

appears. Use

;

button twice

•

onof

for ON

s-hC

button twice to save the

run

is selected. Press

. Use the

and

•

Pid

is selected for PID

button to select

h1C2

for

run

is selected. Press

;

htpd

appears. Use

;

•

button repeatedly

dead

Dead band: dead

band width=positive

Cooling

Set point

positive deadband

dead

Dead band: dead

band width=negative

Cooling

Set point

negative deadband

•

onof

for

•

button to access the

;

button twice to save

run

is selected. Press

dead

Dead band

Cts

Cooling hysteresis

Cooling

Set point

•

button