Automationdirect.com DURApulse GS10 빠른 시작 매뉴얼

{카테고리_이름} Automationdirect.com DURApulse GS10에 대한 빠른 시작 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Automationdirect.com DURApulse GS10 5 페이지.

페이지 인쇄

Automationdirect.com DURApulse GS10 빠른 시작 매뉴얼

DURApulse GS10 AC Drive Quick-Start Guide

GS10 AC Drives Installation Instructions

Sensorless Vector Control Variable Frequency Micro-drive

• Please read this instruction sheet thoroughly before installation and retain for later

reference.

• To ensure the safety of operators and equipment, only qualified personnel familiar

with AC drives should install, wire, program, and operate the GS10 drive. Always read this instruction sheet

thoroughly before using the GS10 drive, especially the WARNING, DANGER and CAUTION notes. If you have any

questions, please contact AutomationDirect.

PLEASE READ PRIOR TO INSTALLATION FOR SAFETY

• The ground terminal of the GS10 drive must be grounded correctly. The grounding method

must comply with the laws of the country where the GS10 drive is to be installed.

• After power has been turned off, the capacitors in the GS10 drive may retain a charge for

several minutes. To prevent personal injury, visually verify that the "CHARGE" LED has

turned off. Then measure to confirm that the DC bus voltage level between terminals (+1)

and (-) is less than 25VDC before touching any terminals. (Capacitor discharge will take at

least 5 minutes for most GS10 models).

• The CMOS ICs on the internal circuit boards of the GS10 drive are sensitive to static

electricity. Please DO NOT touch the circuit boards with your bare hands before taking

anti-static measures. Never disassemble the internal components or circuits.

DANGER

• If wiring changes must be made, turn off power to the GS10 drive before making those

changes. Allow the internal DC bus capacitors in the GS10 drive sufficient time to discharge

prior to making changes in power or control wiring. Failure to do so may result in short

circuit and fire. To ensure personal safety, allow DC bus voltage to discharge to a safe level

before making wiring changes to the GS10 drive.

• DO NOT install the GS10 drive in locations subject to high temperature, direct sunlight, or

flammable materials.

• Never apply power to the output terminals U/T1, V/T2, W/T3 of the GS10 drive. If a fault

occurs during operation of the GS10 drive, refer to the fault code descriptions and corrective

actions to reset the fault before attempting to operate the GS10 drive.

• DO NOT use Hi-pot test for internal components. The semi-conductors in the GS10 drive are

WARNING

easily damaged by high voltage.

• Long motor lead lengths may result in reflective wave due to impedance mismatch between

the motor cable and the motor. Reflective wave may damage the insulation of the motor.

To avoid the possibility of reflective wave damage, use an inverter-rated motor with an

insulation rating of 1600 volts. A load reactor installed between the GS10 drive and motor

will help to mitigate reflective wave.

• Nominal supply voltage to the GS10 drive should be less than or equal to 120/240/480 volts

AC depending on GS10 model.

• Nominal supply current capacity should be less than or equal to 100kA for all GS10 models.

• The GS10 drive must be installed in a clean, well-ventilated and dry location, free from

corrosive gases or liquids.

CAUTION

• The GS10 drive must be stored within an ambient temperature range from –40°C to +85°C,

and relative humidity range of 0% to 90% without condensation.

• Do not apply AC power to the GS10 drive with the front cover removed. Following a fault of

the GS10 drive, wait 5 seconds before pressing the RESET key.

• To improve power factor, install a line reactor ahead of the GS10 drive. Do not install power

correction capacitors in the main AC supply circuit to the GS10 drive to prevent drive faults

due to over-current.

Minimum Wiring

• AC input power to R/L1, S/L2, T/L3 (for single-phase input, use two of the terminals) (For applicability of 1-phase

input power, please refer to Chapter 1 of the DURApulse GS10 AC Drives User Manual at AutomationDirect.com.)

• Ground from the power supply

• Drive power to the motor (U, V, W on T1, T2, T3) (For use with 3-phase motors only!)

• Ground to the motor

With this minimal wiring, the drive can be operated via the keypad to test the motor and drive installation.

See the "Parameter Set Up"

(page

4) section to configure the drive for keypad operation.

Recommended Safety Wiring

We strongly recommend that customers configure a multifunction input as the Emergency Stop to stop the

drive in an emergency situation.

To configure this feature, set any multifunction input to selection 28 (Emergency Stop EF1) and wire a relay or

E-stop pushbutton to the configured input.

GS10_QSP 1st Edition 06/15/2022

Wiring Diagrams

RFI Jumper Removal

If the power distribution system supplying the GS10 AC drive is a floating (IT) or an

asymmetric ground system (including most 120V inputs), the RFI jumper must be

removed.

Removing the RFI jumper uncouples the internal RFI capacitor (filter capacitor)

between the GS10 drive frame and circuitry to avoid damaging those circuits and

(according to IEC 61800-3) to reduce ground leakage current.

GS10 Frame A through D

Main Wiring (Power Circuit)

For main (power) wiring terminal specifications, Please refer to "Specifications for Wiring Terminals –

Main-Circuit Terminals"

(page

2).

GS10 all Frames

*(Note that 1-phase only drives do not have a T/L3 terminal. 120V drives do not have DC- or DC+

terminals).

DC reactor (optional)

Input: one-phase / three-phase* power

Brake resistor (optional)

Jumper

Circuit Breaker or Fuse

R/L1

S/L2

T/L3*

It is recommended that

you install a protective

circuit at R1 – R1C to

R1C

protect the drive from

OFF

damage.

When a fault occurs, the MC contactor

switches to OFF to shut off the drive input

power and protect the power system.

R1 and R1C are the relay output terminals.

GS10 Control Terminal Wiring

Default functions

set via Parameters

P02.00 - P02.05

Default functions set via Parameter P03.00

DI1

DI2

DI5

Motor

U/T1

V/T2

DI1

W/T3

DI2

DI5

GS10 AC Drive Quick-Start Guide – 1st Ed 06/15/2022

Functions set via Parameter P02.13

R1O

FWD(DI1)

REV (DI2)

R1C

DI3

DI4

DI5

Functions set via Parameter P02.16

DO1

DOC

See User Manual Chapter 2 for

sink/source wiring examples

AO1

Functions set via Parameter P03.20

(SG+ Pin5, SG- Pin4, SGND Pin3,7)

DI1

DI2

DI5

DI1

DI2

DI5

Page 1