ADEMCO 4208U 설치 및 설정 매뉴얼

{카테고리_이름} ADEMCO 4208U에 대한 설치 및 설정 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. ADEMCO 4208U 4 페이지. Universal eight zone remote point module

페이지 인쇄

FEATURES

The ADEMCO 4208U Remote Point Module (RPM) is an 8-

zone expander that allows use of available expansion zones

provided by ADEMCO controls that support polling loop

devices. Characteristics of this device include:

•

Can be optionally powered from an external DC power

supply to reduce the amount of current draw from the

polling loop.

•

Uniquely identifies 8 EOLR supervised zones (all zones

use 10k resistors, supplied).

•

DIP Switches can be used to set zone numbers or serial

numbers.

•

When used in the serial number mode, each serial

number in the selected group can be assigned to any

zone number.

•

Loops A & B can be programmed for fast (10msec)

response.

•

Tamper protected.

MOUNTING

Power

before proceeding.

Be sure to mount the 4208U before

making any wire connections

For all fire (NFPA) and UL Commercial

U L

Burglary installations, the 4208U must

be tamper protected or mounted in a

tamper-protected cabinet.

When mounted remotely, tamper protection is required.

Holes on the back of the module's housing permit it to be

mounted horizontally or vertically. Wires can exit from the

side or the breakout on the back of the housing. To enable

tamper protection, set DIP Switch 8 to OFF and attach the

tamper magnet (provided) (Figure 1) to the module inside

cover. Be sure to enable the expansion zone tamper option

at the control (program field *24 = 0). If the module's cover

is removed, the magnet attached to the cover (positioned

near the reed switch) will cause a tamper signal to be sent

to the control for every active zone on the 4208U module.

When the installation is complete, install the cover and affix

the Serial Number and Zone Assignment Tables to the

inside cover of the control.

When mounted inside the cabinet with the control, the

4208U should be mounted horizontally and does not need

tamper protection, provided the cabinet is supervised.

Insert two screws into the raised metal tabs leaving the

heads app. 1/8" exposed, then hang the 4208U using the two

slots on the back.

INSTALLATION AND SETUP GUIDE

should

disconnected

Universal Eight Zone Remote

1. INSERT BOTTOM TABS FIRST.

2. ENGAGE TOP WITH CLIP.

Figure 1. Tamper Magnet Installation

WIRING

For CE installations ADEMCO N6361

EMI suppression bead is

C E

Refer to the N6361 installation guide for

wire routing instructions.

Polling loop and protection loop wires can be brought in

either through the back or front of the unit by removing the

knockouts. Use 22 gauge twisted pair wire for polling loop

connections.

All protection loops use 10k EOL resistors

(included). A maximum resistance of 300 ohms is allowed

on protection loops (excluding EOLR). See Figure 2 for all

connections. Keep in mind that connections to the polling

loop are always required, while power supply connections

are optional.

DIP SWITCH SETTINGS

Zone Assignment Mode:

In the zone assignment mode, the DIP Switches on the 4208

are used to assign the unit to a group of 8 consecutive zones.

These zone numbers, once designated for the 4208U, cannot

be used for anything else, even if you don't use all 8. Follow

the steps below using Table 1 for DIP Switch settings.

Serial Number Mode:

In the serial number mode, the DIP Switches on the 4208U

are used to assign the unit to a group of 8 serial numbers.

You can assign any serial number to any zone number

(except hardwire zone numbers of the control) and you do

not lose zone numbers if you don't use all eight loops on the

4208U. Follow steps below using Table 2 for DIP Switch

settings.

N8215V4 5/01

4208U

Point Module

4219-002-V0

required.