Automotive tyrecheckers 빠른 시작 매뉴얼
{카테고리_이름} Automotive tyrecheckers에 대한 빠른 시작 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Automotive tyrecheckers 2 페이지. Cars and 4x4s • motorcycles caravans and rvs
페이지 인쇄Please Read Instructions Before Installation.
Refer to the Parts Schematic Picture of Alert Cap on Front Page of insert
1
2
Set the tyre to preferred pressure
Twist cap on with fingers then hex key Calibrate top of cap using end of key
4
5
Unscrew cap & confirm it flashes
Re-attach cap firmly using hex key
Check the tyre pressure and inflate to recommended vehicle pressure, before attaching
1
the alert caps. To help uniformity always check pressure on cold tyres ( ie not driven)
Use your fingers initially to begin to screw the alert caps clockwise onto the valve stem
2
thread. Once alert cap engaged onto thread place the Hexagon part of the key ( or 15mm ,
6 point socket) over the top section of the alert cap. Continue to twist clockwise with the
key, all the way until firm at the bottom of the valve stem.
Place the Calibration Fork, (end part of the key) into the Calibration Key Groove, on the top
3
section of the Alert Cap. Twist the top section of the cap approx 2 rotations until firm.
IMPORTANT The alert cap is now calibrated to the current tyre pressure. To verify proper
4
installation, unscrew the cap with the hexagon key, and it will flash red every 1.5 secs if
calibrated correctly.
Screw the alert cap back on firmly using the hexagon key provided.
5
cap could potentially cause a flat tyre so screw on tight to bottom of valve stem thread.
Push on the optional dust cover. This helps protects the cap and also aids the visibility and
6
brightness of the flashing LED. The alert cap will now monitor your tyre pressure 24/7.
IMPORTANT If the tyre pressure drops 4psi the LED light will flash red. Remove the key and
store it in a safe place. You will need the key to reinflate tyres , recalibrate or change alert
cap batteries.
The LED ALERT CAP has a free
spinning stainless sleeve which
prevents the unit from being
removed without the special
key (included).
anti-theft
Distributed by Tyrecheckers Pty Ltd.
For more information or to re-order replacement batteries
go to www..tyrecheckers.com.au or contact us by email on
[email protected] or phone 1300 789 549.
MADE IN CHINA
Patented Worldwide
Automotive Upgrade Technologies
www.automotiveupgrade.com
Insert_SSAT2N.indd 2-3
3
6
Attach optional dust cover
IMPORTANT A loose
IMPORTANT If the tyre pressure drops 4
psi the LED light will flash red. Then after
reinflation, the cap only resets back to a
non-flashing mode, if the tyre pressure is
back to at least the initially calibrated
pressure.
FOR WARRANTY, SAFETY AND TECHNICAL
INFORMATION, SUCH AS RECALIBRATING OR
CHANGING BATTERIES SEE INSIDE INSERT.
*A Heavy Duty Version (60-170psi) also available
TYRE PRESSURE
Can recalibrate pressure setting and change batteries
New Silicon Dustcaps that increase LED flash visibility
Check Your Tyre Pressure
At A Glance.
Maintaining the correct
tyre pressure is the
smart way to:
• Save fuel
• Improve safety
• Reduce tyre wear
Anti-theft Device Built-In,
key included
PRESS
UNIT
psi/kPa
15 mm Hex
Calibration Fork
Optional Silicone Cap
(Enhances Visibility)
PLEASE NOTE YOUR
CALIBRATED PRESSURE FOR
FUTURE REFERENCE
For Light Vehicles
(with tyre pressure 10-70psi)
Product code: SSAT2N
Cars and 4x4s • Motorcycles
Caravans and RVs
LED
ALERT CAPS
TM
SAFE
DANGER
Simply replace the dust cap
on your tyre valve
LED flashes red if tyre
pressure drops 4psi
Highly visible night and day
Parts Schematic Picture
DATE
Calibration Key Groove
Calibration Top
Battery
Top
Anti-theft Rotating Cuff
Bottom Hex
13/08/13 8:33 PM