Autonics BS5-P1MD 매뉴얼
{카테고리_이름} Autonics BS5-P1MD에 대한 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Autonics BS5-P1MD 4 페이지. Push button type photomicro sensors
페이지 인쇄
BS5-P Series
Push Button Type Photomicro Sensors
Features
Button operation enables accurate detection regardless of material, color, or
reflectance of target object
Optimized for transport detection of semiconductor wafer enclosures (FOUP,
FOSB, etc.)
Optical detection of button operation guarantees mechanical life cycle of 5 million
operations
Total of 4 red LED indicators (side:2, top:2) for higher visibility of operation status
Increased product durability with steel mounting brackets
Emitter OFF function and check stable operation functions
Built-in reverse polarity protection circuit and output short overcurrent protection circuit
Please read "Safety Considerations"
in the instruction manual before using.
Specifications
NPN open collector
output
Model
PNP open collector
output
※1
Operation method
Stop position
Button
Output switching
operation
position
※2
Operation limit position Below 0mm
※3
Operation load
Power supply
Current consumption
Light source
Operation mode
Control output
NPN output
External
※4
PNP output
input
Response
Protection circuit
Indicator
Insulation resistance
Noise immunity
Dielectric strength
Vibration
Shock
Mechanical life cycle
Ambient illuminance
Environ-
Ambient temperature
ment
Ambient humidity
Protection structure
Material
Cable
Approval
※5
Weight
※1: Detection occurs when the button is pushed and the light source is blocked.
※2: Stop position: position of the button without any applied pressure
Output switching position: position where the output switches ON/OFF
Operation limit position: position of the button when fully pushed
Stop position
Operation limit
position
※3: Pressure required to push the button from stop position to output switching position
※4: External input when using emitter OFF function or check stable operation functions.
※5: The weight includes packaging. The weight in parenthesis is for unit only.
※The temperature and humidity of environment resistance are rated at non-freezing or condensation.
A-136
BS5-P1ML
BS5-P1ML-P
Push button type
5.0±0.4mm
4.0±0.5mm
Max. 3N (max. 0.3kgf)
12-24VDC
±10% (ripple P-P: max. 10%)
Max. 35mA
Infrared LED (940nm)
Light ON
(output OFF when button is pushed)
NPN or PNP open collector output
·Load voltage: max. 26.4VDC
Emitter OFF: short at 0V or max. 0.25VDC
Emitter ON: open (leakage current max. 0.4mA)
Emitter OFF: short at +V or min. -0.25VDC
Emitter ON: open (leakage current max. 0.4mA)
Under 1ms
Reverse polarity protection circuit, output short overcurrent protection circuit
Operation indicator: red LED
Over 20MΩ (at 250VDC megger)
±240V of square wave noise (pulse width:1 ㎲) from the noise simulator
1,000VAC at 50/60Hz for 1min
1.5mm amplitude at 10 to 55Hz frequency in each X, Y, Z direction for 2 hours
500m/s² (approx. 50G) in each X, Y, Z direction for 3 times
Min. 5,000,000 operations
(1 operation = stop position - operation limit position - stop position)
Fluorescent lamp: max. 1,000lx (receiver illuminance)
-20 to 55℃, storage: -25 to 70℃
35 to 85%RH, storage: 35 to 85%RH
IP40 (IEC standard)
Case: polycarbonate + glass fiber, button: polyoxymethylene, sleeve: SUS304 (steel use stainless 304)
Ø3mm, 4-wire, 1m
(AWG 28, core diameter: 0.08mm, no. of core wires: 19, insulator diameter: Ø0.88mm)
Approx. 50g (approx. 30g)
Output switching position: 4.0±0.5mm
BS5-P1MD
BS5-P1MD-P
Dark ON
(output ON when button is pushed)
·Load current: max. 50mA ·Residual voltage: max. 1VDC
(outflow current max. 30mA)
of +V (absorption current max. 30mA)