Dynamite PASSPORT Ultra Duo 설치 매뉴얼 - 페이지 3

{카테고리_이름} Dynamite PASSPORT Ultra Duo에 대한 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Dynamite PASSPORT Ultra Duo 10 페이지. 100w lcd ac/dc multi-chemistry battery charger
Dynamite PASSPORT Ultra Duo에 대해서도 마찬가지입니다: 사용 설명서 (2 페이지)

페이지 인쇄

1. Press the Left and Right Arrows on the LCD Touch Screen to scroll through the

main menu screens.

2. Press the action at the bottom of the LCD Touch Screen to enter that menu.

3. Press a parameter to highlight that parameter.

4. Press the Up and Down Arrows to edit the parameter.

1 - SELf TEST AND PrOgrAM SELECT SCrEENS

When the charger is powered ON, there is a series of self tests and the screen will show the

charger brand name and model number.

CAUTION: If at any time during the charge process the battery pack becomes hot or begins to puff disconnect the battery immediately and discontinue the charge process as batteries can

cause fire, collateral damage and injuries.

CAUTION: Using a charge rate that is not compatible with the battery capacity may result in damage or malfunction of the charger or battery.

CAUTION: The Lithium charge program menus are to be used ONLY for the charging and discharging of Lithium battery packs. Charging other battery types using the Lithium charge programs

will damage the battery or the charger.

Only Li-Po is shown in the following three sections. Li-Ion/Li-Fe menus differ ONLY in Cell and Pack Voltage values.

2 - LIThIUM (LI-PO/LI-fE/LI-ION) ChArgINg

1. Connect the banana plugs of the battery adapter cable to the Power Output Black (–) (A)

and Power Output Red (+) (B), making sure that the positive and negative connectors are not

reversed.

2. Connect the JST_XH balance adapter to the Balance Circuit Adapter Board Connector (C).

3. Connect the battery connector to the battery adapter cable.

4. Connect the balance connector of the battery to the JST_XH balance adapter.

5. Press the Left and Right Arrows on the LCD Touch Screen to scroll through the main menu

screens until you reach Program Select=Li-Po/Li-Ion/Li-Fe.

Program select=LiPo

CHG

6. Press CHG.

LiPo CHARGE

Pack.Volt.

Capacity

Current

End Cell Volt

Press&Hold

BACK

7. Press a parameter to highlight that parameter.

8. Press the Up and Down Arrows to edit the parameter.

9. Press Select to save the parameter.

10. Once the parameters are at the desired settings, press and hold CHARGE.

11. The charger will check the battery and charger settings and charging will begin. The charger

will beep and display the following screen:

LiPo CHG

Capacity

Current

Voltage

Resistance

Peak Temp.

PrOgrAMMINg qUICk gUIDE

OPErATINg YOUr ChArgEr

LiPo

DCHG

STOR

11.1V/3S

1050mAh

1.0A

4.20V

CHARGE

SELECT

000:11S

11mAh

4.0A

8.00V

****mΩ

No sens

5. Press Select to save the parameter.

6. If there is more than one screen of parameters, press the top right corner of the LCD Touch

Screen to scroll through the parameter screens.

7. Press Back to return to the main menu screens.

12. Press the arrow in the top right of the LCD Touch Screen to see the rest of the Charging

information.

13. Press Unit to see the voltages for each cell. Press Back to return to the charging screen.

DATA LiPo–CELLS

1 > 3.97

2 > 3.98

3 > 0.00

4 > 0.00

5 > 0.00

6 > 0.00

14. Press Graph to see the battery voltage graph. Press Back to return to the charging screen.

Data LiPo = Graph

15. Press STOP at any time to stop charging.

16. When charging is complete, the charger will sound a series of beeps and display the following

screen:

LiPo DONE

Capacity

Current

Voltage

Resistance

Peak Temp.

17. Disconnect the battery from the charger.

BACK

010:28S

169mAh

0.0A

8.00V

****mΩ

No sens