Dynamite Prophet Plus II 사용자 설명서 - 페이지 2

{카테고리_이름} Dynamite Prophet Plus II에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Dynamite Prophet Plus II 2 페이지. Ac/dc powered peak detection fast charger for 4- to 8-cell ni-cd & ni-mh batteries
Dynamite Prophet Plus II에 대해서도 마찬가지입니다: 매뉴얼 (6 페이지)

페이지 인쇄

Introduction

Thank you for purchasing the Prophet Plus II AC/DC Peak Detection Charger. Charging 4-8 cell NiCd and NiMH

battery packs safely and efﬁciently has never been so easy. Just select a charge rate of 1, 2 or 4 amps and press

the start button. The charger will automatically stop fast charging when it senses that the pack is fully charged and

enters a safe trickle charge mode to equalize cell voltage and maintain full charge.

A switching AC power supply allows for the small case size and the electric cooling fan keeps the charger's

temperature low for long life.

The beeper can be turned on and off by holding down the start button for quiet charging. Hold down the

"Start" button until the LED quickly ﬂashes ﬁve times, signifying the Beeper has been turned off. Hold the

"Start" button down again until the LED ﬂashes and the beeper beeps quickly ﬁve times, indicating the beeper

has been turned back on.

Features

1. 110V AC power cord

2. 12V DC power cord with alligator clips

3. Charge rates of 1, 2, or 4 amps

4. LED and beeper indicate when charge is complete

5. Cooling fan

6. Tamiya-style connector

Additional Features

• Receiver pack charge lead adapter included

• Charges 4- to 8-cell Ni-Cd or Ni-MH battery packs

• Limited 5-year warranty

• Advanced trickle charge

• Advanced peak detection circuitry

• Ni-Cd and Ni-MH compatible

Supplying power to the charger

This charger can be powered by connecting it to a standard 110V wall outlet or by using the provided alligator clips

to connect the charger to a 12V DC power source, such as a 12V hobby battery (HAN102), a 12 volt power supply

or an automobile battery. Do not use both an AC & DC source at the same time.

If you power the charger by using DC power, connect the red (positive) end of the alligator clips to the red terminal

of the DC power source and the black (negative) end of the alligator clips to the black terminal of the DC power

source. If you choose to power the charger with an automobile battery, never do so with the automobile running!

Charging 6- & 7-Cell Ni-Cd or Ni-MH Battery Packs

1. When power is supplied to the charger, the charger will beep, and the LED will ﬂash once.

2. Connect the battery pack to the charger, and the charger will beep again, The LED will repeatedly blink until you

begin the charging process.

Note: For optimum performance, charge 8 cell packs using an AC power source.

3. Select the charge rate based on the batteries capacity rating. See "Charge Times" chart on Page 3.

4. Push the Start button to begin the charging process. The LED will be solid red during the charging process.

5. Once the battery has peaked, the LED will ﬂash, and the beeper will sound for 30 seconds. If the battery is

left connected after 30 seconds, the LED will continue to ﬂash, and the beeper will sound approximately

every 90 seconds.

When the battery has peaked, the Prophet Plus II will automatically transition to Advanced Trickle Charge.

Charging 4- & 8-Cell Ni-Cd or Ni-MH Radio Packs

1. When power is supplied to the charger, the charger will beep, and the LED will ﬂash once.

2. Connect the battery pack to the charger using the included RX charge adapter, and the charger will beep again,

The LED will repeatedly blink until you begin the charging process.

3. Select a charge rate of either 1 or 2 amps, depending on the receiver pack you are going to charge. We

recommend that you charge 600mAh or lower capacity receiver packs at 1 amp, while you may charge higher

capacity packs at 2 amps.

4. Push the Start button to begin the charging process. The LED will be solid red during the charging process.

5. Once the battery has peaked, the LED will ﬂash, and the beeper will sound for 30 seconds. If the battery is

left connected after 30 seconds, the LED will continue to ﬂash, and the beeper will sound approximately

every 90 seconds.

When the battery has peaked, the Prophet Plus II will automatically transition to Advanced Trickle Charge.

Note: When you connect the charger to a power source, the charger will beep. The charger also beeps

when a battery has been successfully connected. The LED will illuminate to indicate the battery is charging.

Once the battery has peaked, the LED will ﬂash, and the charger will beep repeatedly.

Advanced Trickle Charge

Once the batteries are fully charged, the charger will immediately enter a pulse trickle charge. This pulse trickle

charge will condition the batteries, extend their life and make certain that they are fully charged when you are ready

to use them. You will know that the charger has entered Advanced Trickle Charge when the charger beeps and the

LED continuously ﬂashes.

Re-Peak

Once the battery pack has peaked and is on Advanced Trickle Charge, you can re-peak the battery by simply

pushing the Start button without disconnecting the battery from the charger. Do not re-peak the battery more than

once during a charging process.