Hifonics BE35 800.4 빠른 시작 설치 매뉴얼

{카테고리_이름} Hifonics BE35 800.4에 대한 빠른 시작 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Hifonics BE35 800.4 2 페이지.

페이지 인쇄
Hifonics BE35 800.4 빠른 시작 설치 매뉴얼
Before you start
CAUTION
Many new and factory radios require a reset code when
disconnected from battery power. This is an anti-theft
feature. Before unplugging power, you must determine if
your radio/source unit requires a reset code. Check the
operation manual for your vehicle or contact the dealer.
Power cable size
Model
and fusing
It is critical to use the proper power
BE35-500.4
and ground cable. Select the size
listed here for your amplifier model.
BE35 800.4
Always use high quality copper
BE35 1200.1D
1 x 80A Maxi
cable. Visit our website for multi amp
system cable recommendations.
2 x 70A Maxi
BE35 1700.1D
External 200A
BE35 2100.1D
Be sure to use the proper fuse size
for each model. Some models require
External 250A
BE35 2500.1D
an external fuse.
External 100A
BE35 5000.5
Installation
Disconnect
1
negative battery
terminal
Place terminal in a secure
position so that it won't
accidentally contact the
negative battery post
Run Cables
2
Properly route power,
speaker and RCA cables
through the vehicle.
Mount Amplifier
3
Choose a mounting location
that will provide adequate air
ventilation. Mount the amplifier to
a secure surface. Do not mount
the amplifier upside down.
Chassis Ground
4
The chassis ground connection
is critical to the performance
of the amplifier. Choose a
location that is close to the
amplifier. Completely scrape
away the paint and use a nut
and bolt if possible.
DO NOT USE AN EXISTING
FACTORY BOLT!
Fuse Size
Cable Size
Negative Power
5
Connection
4ga
2x25A ATC
Attach the chassis ground
4ga
2x35A ATC
cable to the amplifier
4ga
negative terminal. It is
important to make sure this
2ga
connection is very tight.
0ga
Remote Turn-on
6
0ga
Connection
2ga
Attach the remote turn on
wire to the amplifier remote
output of the source unit.
Positive Power
7
Connection
Attach the main power cable
to the amplifier +12V. The
cable must run directly to
the battery and be properly
fused and be very tight.
Signal Input
8
Connection
Connect the RCA cables to
the INPUT connectors. The
OUTPUT can be used to
provide input for a second
amplifier.
9
Level Control
Bare metal
BRIDGED
LEFT
RIGHT
SPEAKER
OUTPUT
BRIDGED
BRIDGED
BRIDGED
LEFT
RIGHT
LEFT
RIGHT
CH 3
CH 4
SPEAKER
OUTPUT
SPEAKER
OUTPUT
SPEAKER
OUTPUT
BRIDGED
BRIDGED
LEFT
RIGHT
CH 1
CH 2
SPEAKER
OUTPUT
SPEAKER
OUTPUT
SPEAKER
BRIDGED
CH 3
CH 4
SPEAKER
OUTPUT
Turn the LEVEL control completely
INPUT
INPUT
counter-clockwise to minimum.
LEVEL
LEVEL
SUBSONIC
15
9V
0.2V
6V
0.2V
PHASE
LPF
LPF
Speaker
10
Connections
BRIDGED
BRIDGED
LEFT
RIGHT
CH 3
CH 4
Connect the speaker cables to
the speaker output connectors.
SPEAKER
SPEAKER
OUTPUT
Follow the diagram below
SPEAKER
OUTPUT
that best fits your speaker
configuration.
Stereo
BRIDGED
BRIDGED
BRIDGED
LEFT
RIGHT
CH 1
CH 2
LEFT
RIGHT
BRIDGED
CH 3
CH 4
SPEAKER
OUTPUT
SPEAKER
OUTPUT
SPEAKER
SPEAKER
SPEAKER
OUTPUT
SPEAKER
OUTPUT
BRIDGED
BRIDGED
CH 3
CH 4
LEFT
RIGHT
Monoblock
single woofer
BRIDGED
SPEAKER
OUTPUT
SPEAKER
CH 1
CH 2
SPEAKER
OUTPUT
SPEAKER
OUTPUT
SPEAKER
OUTPUT
SPEAKER
OUTPUT
BRIDGED
CH 3
CH 4
Positive Battery
11
Connection
SPEAKER
OUTPUT
OUTPUT
SPEAKER
OUTPUT
Connect the power cable to the
positive battery terminal. The
power cable must be fused
within 18 inches of the battery
terminal.
Be prepared to disarm your vehicle's alarm and
to enter your radio / source unit code.
Re-connect
12
Negative Battery
Terminal
XOVER
MODE
Re-connect the negative
SUBSONIC
battery terminal making sure it
is securely tightened.
MONO STEREO
FULL
HP
LP
35Hz
10
40Hz
XOVER
MODE
LPF
OUTPUT
SPEAKER
OUTPUT
Bridged
BRIDGED
CH 3
CH 4
OUTPUT
SPEAKER
OUTPUT
SPEAKER
OUTPUT
SPEAKER
OUTPUT
SPEAKER
OUTPUT
BRIDGED
CH 1
CH 2
Monoblock
multiple woofers
BRIDGED
OUTPUT
SPEAKER
OUTPUT
SPEAKER
LEFT
RIGHT
SPEAKER
OUTPUT
SPEAKER
OUTPUT
BRIDGED
CH 3
CH 4
SPEAKER
OUTPUT
SPEAKER
OUTPUT
SPEAKER
OUTPUT