Dynamix 20km 10/100/1000WDM B 사용자 설명서 - 페이지 2

{카테고리_이름} Dynamix 20km 10/100/1000WDM B에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Dynamix 20km 10/100/1000WDM B 2 페이지. Wdm 10/100/1000m, gigabit ethernet

페이지 인쇄

Dynamix Gigabit WDM Single fiber

dual-direction fiber optic media

converter

1.Overview

Dynamix single-fiber dual-direction fiber optic

media converter be used Ethernet's electric

signal to transmit optic signal 's electricity signal

transceiver, the feature is adopt one fiber cable

can receive and transmit optic signal in-phase,

enhance one double transmit energy than existing

optical fiber, economized fiber cable's source.

Dynamix single-mode single-fiber series is a self-

adapted single-fiber dual-direction fiber optic

media converter with 10/100/1000M, it's protocol

IEEE802.3ab, IEEE802.3u,10Base-T,

100Base-TX, 1000Base-TX, 1000Base-SX,

1000Base-LX's standard and passed the

information industry ministry's telecom equipment

enter networking examination. Dynamix single-

mode single-fiber is a gigabit single-mode single-

fiber media converter with 1000M.

Due to single-fiber dual-direction media

converter's transmit optic signal transmit

wavelength and receive wavelength are

difference, so must be use by pair - Dynamix -

20km 10/100/1000WDM A and Dynamix -20km

10/100/1000WDM B, for example. One TX and

one RX, be one pair, can't use to wrong, If not

will can't working normal. Singlemode single-

fiber's transmit optic signal is wavelength

1550nm, receive optic signal is wavelength

1310nm; single-fiber dual-direction media

converter have one RJ-45 interface and one SC

single-core interface, separate by twisted-pair

and fiber to connecting. Single-fiber media

converter have 6 LED indicator: POWER,

SPDFX1000, SPDTX1000, FX Link/ACT,

TX Link/ACT, FDX.

2. Specification and Feature Explain

1. Accord with IEEE802.3ab/z, IEEE802.3u,

IEEE802.3x, IEEE802.1q 100Base-T, 100BASE-TX,

1000Base-TX, 100Base-SX, 1000Base-LX standard.

2. Support TCP/IP PPPOE DHCP ICMP NAT protocol

3. Flow control mode: full duplex adoptIEEE802.3X, half

duplex adopt Backpressure's standard.

4. Electricity port support auto-negotiation function,

auto-regulation transmit mode and transmit speed.

5. Support Auto-MDI/MDIX automatic reverse.

6. Support storage transmit mode, capability is 256K.

7. Support electricity port's 1000M mode or self-adapt

mode's switch.

8. Afford of state indicator, external power

(output 5V-50HZ 1A)

9. Interface: electric port - RJ-45, fiber port - SC

10. Twisted-pair: CAT.5 CAT.6

11. Singlemode fiber: 8/125, 8.3/125, 9/125µm

12. Working temperature: 0~50°С

13. Storage temperature:-20~70°С

14. Humidity: 5% ~ 90% (non-condensing)

15. Size: 32*128*158mm(H*W*L)

3.Installed and Initialization

Please use the follow approach installed single-fiber

dual-direction fiber optic media converter:

1.Connecting optical cable, pay attention to matching

with TX and RX fiber link by two media converter, don't

put the interface by the same to directness connection

2. Put UTP jump cable through networking

equipment connecting to single fiber media

converter's

RJ-45

interface,

converter's

electricity

port

through line and intersection line.

3. Put power adapter's DC plugs pin connect to

fiber optic media converter's DC plugs pin, then

receptacle

the

power

connecting power.

4. Here you can put self-check gradation make

the indicator fulgurate, so the fiber optic media

converter's power would be light, after self-

check you should warranted fiber optic media

converter's test to decided media converter

electricity port's working state and the couple

networking equipment electricity port state.

If can't test the couple equipment, media

converter's electricity port's state uncertainty,

so TX Link and SPD/TX 1000 indicator can't

light. If the electricity port connecting right, FX

Link SPD would be light.

4. LED Indicator

Single fiber dual-direction media converter have

6 LED indicator, they would be show media

converter's

working

state,

shows, that would estimated, if the media

converter working normal or have any wrong,

that help us find the fault. the function will

separate

explain

1. PWR: be light shows DC5V power adapter

working normal

2. Speed is 1000 Mbps, extinguish shows fiber

transmit speed less than 1000Mbps.

3. FX Link/Act: light fiber link connecting right,

fulgurate shows transmitting data.

4.FDX: be light shows fiber use full duplex mode

to transmitting data.

the

media

can

self-adapt

adapter,

warranty,

LED

follow: