Hifonics XXV XXV Maxximus 사용자 설명서 - 페이지 13

{카테고리_이름} Hifonics XXV XXV Maxximus에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Hifonics XXV XXV Maxximus 20 페이지. Xxv edition high performance amplifier

페이지 인쇄
Hifonics XXV XXV Maxximus 사용자 설명서
XXV MAXXIMUS DUAL MONO BLOCK AMPLIFIER APPLICATIONS
BASIC APPLICATION
The 2 channel mono amplifiers are capable of 4, 2 & 1 Ohm loads wired channels 1 & 2
independent as shown below or 4 or 2 Ohms wired mono bridged shown below.
The XXV-MAXXIMUS has two 5000 watt D-Class channels built-in labeled Subwoofer 1
& Subwoofer 2 on the end panel.
SINGLE AMP INSTALLATION PROCEDURE:
1. Connect the amp LINE INPUTS to the Radio/CD player full range or mono line out puts with good
quality RCA interconnect cables.
2. Plug in the XXVR-1 bass remote module into the amp REMOTE INPUT jack.
3. Route two 0 gauge power cables directly to the vehicle battery with an in-line 300 amp fuse.
DESIGNATED MONO
LINE INPUT
USING CHANNELS 1 & 2 INDEPENDENTLY
POWER
GND
+12V
REM
POWER
GND
+12V
-
Note: The amp is capable of driving 4, 2 or 1-Ohm per sub in this configuration
Impedances below 1-Ohm will damage the amplifier
FULL RANGE
STEREO LINE INPUT
NOT USED
SUBWOOFER 1
POWER
-
-
+
+
+12V
GND
POWER
-
+12V
GND
+
+
SUBWOOFER 2
This will allow you to operate separate subs independently (on each channel 1 or 2) at 4, 2 or
1 Ohm at up to 5000 watts or bridged across 1& 2 to operate a single sub up to 10000 watts
at 4 or 2 Ohms.
Note: The amp is not capable of 1 Ohm when bridged across 1 & 2.
The crossovers and XXVR-1 Bass Remote Module will operate both 1 & 2 channels
simultaneously.
4. Connect two 0 gauge ground cables directly to chassis ground with in 36" of the amp.
- Be sure to remove any paint or primer from the ground point.
- Use a nut, bolt and lock washer to secure the ground cable to the chassis ground.
5. Connect the subwoofer(s) in accordance to the diagrams below.
Y-ADAPTOR
Note: You can use the Radio/CD designated mono line
output or a full range stereo line output. For full range
stereo line output, you will need an optional "Y-Adaptor"
as shown
USING CHANNELS 1 & 2 MONO BRIDGED
POWER
GND
POWER
GND
Note: The amp is capable of driving 4 or 2-Ohms in this configuration
Impedances below 2-Ohms will damage the amplifier
TO BATTERY +12v VIA FUSE
REMOTE TURN-ON
TO BATTERY +12v VIA FUSE
SUBWOOFER 1
-
-
+12V
+
+
REM
BRI
DGI G UM
N J
+12V
-
-
+
+
SUBWOOFER 2
Caution: You must place a 12 gauge mono
Bridged Jumper Wire as shown above
CHASSIS GROUND
CHASSIS GROUND
POWER
+12V
GND
PER
POWER
+12V
GND
11