909 909C12V 사용 설명서 - 페이지 8
{카테고리_이름} 909 909C12V에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. 909 909C12V 20 페이지. 12v variable speed oscillating multi tool
페이지 인쇄•
Take care where the tool is stored. Do not store in areas
of corrosive fumes, or salt air or similar conditions. Try
and store the tool in the packaging supplied with the tool.
•
Do not dispose of the battery in a fire or put the battery
into a microwave oven, conventional oven, dryer, or high-
pressure container.
Under these conditions, the battery may explode.
•
Never attempt to open the battery pack, puncture the
battery or subject the battery to strong physical shock.
•
If the plastic housing of the battery pack breaks open
or cracks, immediately discontinue its use and do not
recharge it. Ensure the battery pack clip is in good
condition and will not allow the pack to fall free from the
tool. If the clip is damaged or for any reason is not locking
the pack in place Do Not continue to use.
•
Stop using the battery if it exhibits abnormal heat, odour,
colour, deformation, or is in an abnormal condition.
•
If you detect leakage or a foul odour, it is especially
important to keep the battery away from fire. If battery
liquid leaks onto your skin or clothes, wash well with clean
water immediately. If liquid leaking from the
battery gets into your eyes, do not rub your eyes.
Rinse your eyes well (for at least 10 minutes) with clean
water, and consult a doctor immediately. Do not use a
leaking battery.
•
Handle batteries with care to avoid shorting the battery
with conducting materials, such as nails, screws, metal
watch bands, rings, bracelets, and keys. The battery may
overheat and could burn you.
•
After the battery has reached the end of its useful life, we
recommend recycling the materials at your local municipal
council recycling centre. DO NOT attempt to replace the
battery cells in the battery pack, repair or modify any part
of the battery pack assembly.
•
When recycling, make it nonconductive by applying
insulating tape to the terminals located on the battery.
Important information – Product care
This oscillating tool uses lithium ion battery cells. Care
MUST be taken to ensure both the safety and life of the
pack is maintained. Ensure you have read all of the safety
notes in the previous pages before using the oscillating tool.
Safety devices and circuitry for this tool are located in
the battery pack of this tool. The battery pack is a vital
component, not just for the power source, but also for
the full safety control for both the charging and also the
tool operation. Treat the battery pack with care and within
the guidelines of this manual. If the pack does become
immersed in water or any fluids, or is subject to a severe
drop etc, or it does not operate within the guidelines of
this manual, immediately STOP using the battery pack
and have it checked.
During operation avoid overloading the oscillating tool. If
the oscillating tool is overloaded it will automatically STOP.
Overloading may occur for a number of reasons including
when the oscillating tool is pushed too hard or when using
an attachment greater than what is specified. If you do
overload the oscillating tool during operation refer to the
"Overload" section in this manual.
Note:
When the battery of the oscillating tool is at the lower
end of the charge, the oscillating tool is more susceptible to
the overload condition.
As mentioned above the battery pack is an integral
component of this tool and it is fitted with thermal safety
devices. Running the oscillating tool at close to maximum
load, or continual resetting of the overload will cause the
battery pack to over heat. When a preset cell temperature is
detected, the battery pack will automatically STOP
operating and will not restart until the battery pack has
cooled to a safe level.
In this condition, DO NOT force cool the pack by placing in
a freezer or similar device. Refer to the "Overload" section
in this manual.
8