Autonics TC4S 매뉴얼 - 페이지 7
{카테고리_이름} Autonics TC4S에 대한 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Autonics TC4S 14 페이지. Touch switch type temperature controller
Autonics TC4S에 대해서도 마찬가지입니다: 매뉴얼 (14 페이지), 매뉴얼 (2 페이지), 사용 설명서 (2 페이지), 빠른 시작 매뉴얼 (9 페이지), 빠른 시작 매뉴얼 (10 페이지)
페이지 인쇄
TC Series
Parameter 1 group
Run mode
2 sec.
3 sec.
PAR1
AL1 alarm temperature
AL1
AL2 alarm temperature
AL2
※ 3
Auto-tuning
AT
Proportional band
P
Integral time
1
Derivation time
D
Manual reset
REST
Hysteresis
HYS
Parameter 2 group
Run mode
4 sec.
3 sec.
PAR2
Input type
IN-T
Temperature unit
UNIT
Input correction
IN-B
Input digital filter
MAvF
H-60
※ 1:
: Press any key among
S
※ 2: After checking/changing set value at each parameter, and press
flashes twice and it moves to next parameter automatically.
※ 3: It is displayed when control type parameter [ C-MD ] of parameter 2group is set PID .
※ Press
※
This parameter might not be displayed depending on other parameter settings.
※ 1
S
1250
Set range: Deviation alarm(-[F.S] to [F.S], Absolute value alarm(temperature range)
※ In case alarm operation mode [ AL-1 , AL-2 ], AM)_ / SBa
※ 2
set to [ AL-1 , AL-2 ], no parameters is displayed.
S
1250
S
OFF
ON
S
01)0
Set range: 0.1 to 999.9℃/℉
Set range: 0 to 9999 sec.
S
0000
※ Integral operation will be OFF when set value is "0".
Set range: 0 to 9999 sec.
S
0000
※ Derivative operation will be OFF when set value is "0".
S
Set range: 0.0 to 100.0%
05)0
※ It is displayed in P/PD control.
Set range: 1 to 100℃/℉ (0.1 to 50.0℃/℉)
S
002
※ It is displayed when control type parameter [ C-MD ] of setting group 2 is set ONOF .
※ 1:
: Press any key among
S
※ 2: After checking/changing set value at each parameter, and press
flashes twice and it moves to next parameter automatically.
※ Press
※
This parameter might not be displayed depending on other parameter settings.
CUsL
CUsH
※ 1
S
KCA
※ 2
S
?C
?F
S
000
Set range: -999 to 999 ( DPtL / CUsL : -199.9 to 999.9)
S
Set range: 0.1 to 120.0 sec.
)1
※ Set input digital filter time for average input value affected control, and display value.
,
,
.
key for 3 sec. to return RUN mode at any parameter.
※ It starts to operate auto-tuning when it is ON and set as OFF automatically
after finish the operation.
※ Deviation indicator(▲, ■, ▼) will be flashing(cycle:1 sec.) during auto
tuning function.
,
,
.
key for 3 sec. to return RUN mode at any parameter.
DPtL
DPtH
JIC
LIC
※ Front temperature unit indicator will flash when selecting the unit.
key, set value
/ LBa
of setting group 2 is
key, set value